Käyttöohje Tunturi S30 Stepperi

Käyttöohje

GB

OWNER’S MANUAL

•

S30

3

training partner. Whatever your goal in training,

we are certain this is the training equipment

to get you there. You’ll find information about

using your exercise equipment and what makes

for efficient training at Tunturi’s website at

WWW.TUNTURI.COM.

ASSEMBLY

Unpack the device and check that all the

following parts are in the package (fig. 1):

A. Main mast assembly

B. Leg tubes (2)

C. Tie rods (2)

D. Feet (2)

E. Handlebar

F. Meter mount

G. Meter

H. Shocks (2)

Assembly kit (contents marked with in the spare

part list): keep the assembly tools, as you

may need them e.g. for adjusting the equipment.

If you notice that a part is missing, contact the

dealer and give the model (S30), serial number

and spare part number from the list at the back

of the manual. The assembly figures mentioned

in the text are at the back of the manual. The

package includes a silicate bag for absorbing

moisture during storage and transportation.

Assemble the device as follows (left, right,

front and back are as seen from the exercising

position):

ATTACH THE LEGS

Position the main mast assembly so that the S30

label is facing up. Screw the left leg tube

into the main mast as shown, being careful to

keep the leg tube in line (fig. 2).

NOTE! Do not

force. If resistance is felt initially, unscrew and

start again. Hand tighten the leg firmly. Attach

the right leg in the same manner.

ATTACH THE TIE RODS

Place the hooked end of a tie rod into the left

hole on the bottom of the main mast (fig. 3).

Gently slide the tie rod bracket into the end

of the left tube while simultaneously inserting

the threaded end of the tie rod into the tie rod

bracket. Slide the bracket with the rod into the

tube as far as possible, making sure the bracket

is at right angle to the tie rod. Secure the tie

rod with a 5 mm flat washer and a locking nut.

Tighten the nut with the enclosed flat wrench

(fig. 4). Repeat for the right tie rod.

ATTACH THE FEET

The feet are labeled “L”and “R” (for left and

right). Slide each foot onto its respective leg,

making sure the tie rod connects at the bottom

of the slot (fig. 4). At this time, tilt the unit back

onto the feet.

INSTALL THE SHOCKS

Attach the end of the shock absorber that

contains the resistance adjustment mechanism

to the left side of the main mast. Insert a shock

spacer into the eye of the top end of the shock.

With the arrow facing to the rear, secure the

shock to the outside of the top, left mounting

bracket with a socket head cap screw, two 8 mm

flat washers, and a locking nut. Use the flat

wrench and the 5 mm hex wrench to tighten.

Lift the left foot pedal up and secure the bottom

of the shock repeating the same steps as for the

upper shock attachment (fig. 5). Install the right

shock in the same manner.

ATTACH THE HANDLEBAR

Align the holes on the base of the handlebar to

those on the top of the mast, making sure the

handlebar end caps are pointing forward. Secure

the handlebar with four Allen screws and 6 mm

split lock washers (fig. 6). Tighten screws with

the 5 mm hex wrench.

ATTACH THE METER

Open the battery case cover on the back of the

meter case and insert two 1.5 V AA-batteries to

the battery case following the + and - markings.

Feed the meter wire, coming out through the top

of the vertical frame, through the meter mount

and snap the meter mount over the handlebars,

making sure the tongue on the handlebar mount

aligns with the corresponding groove on the

meter mount (fig. 7).

NOTE! Be careful not to

get the wire caught! Plug the meter cable into

the socket on the rear of the meter. Secure the

meter into place by setting it on the meter mount

and sliding it down until firmly in place.

NOTE!

Make sure the meter cable is not pinched during

the assembly as this can cause the meter to not

function correctly (fig. 8).

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Tunturi S30 Stepperi. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Tunturi. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Tunturi S30 Stepperi käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Tunturi Stepperit
Lisää Stepperit käsikirjoja

Usein kysytyt kysymykset kohteesta Tunturi S30 Stepperi

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Tunturi S90 Stepperi

Käyttöohje

Crivit IAN 280567 Stepperi

Käyttöohje

Crivit IAN 89664 Stepperi

Käyttöohje

Crivit IAN 290933 Stepperi

Käyttöohje

Crivit IAN 270017 Stepperi

Aiheeseen liittyvät luokat