Käyttöohje Black and Decker GTC5455PCB Pensasleikkuri

Käyttöohje

8

ENGLISH

(Original instructions)

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a

service center for recycling.

State of charge indicator (Fig.B)

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery during use and during charging. It does not indicate

tool functionality and is subject to variation based on product

components, temperature and end-user application.

Checking state of charge during use

u Press the state of charge indicator button (B1).

u The three LEDs (B2) will illuminate, indicating the percent

of charge in the battery. See chart in gure B.

u If LED light does not illuminate, charge battery.

Charger Diagnostics (Fig.E)

Refer to the indicators in gure E for the charge status of the

battery pack.

Bad Battery

If you see a bad battery blink pattern, do not continue

to charge this battery. Return it to a service center or a

collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode.

This feature ensures maximum battery pack life. A cold battery

pack will charge at a slower rate than a warm battery pack.

The pack will charge at that slower rate throughout the entire

charging cycle and will not return to maximum charge rate

even if the pack warms.

Installing and removing the battery pack from the

tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack Fig. C)

u Insert battery (10) into tool until an audible click is heard

(Figure. C)

u Ensure battery pack is fully seated and fully latched into

position.

To remove battery pack (Fig.D)

u Depress the battery release button (10a) as shown in

gure D and pull battery pack (10) out of tool.

Dualvolt 54V Battery Pack (Fig F.)

The Dualvolt 54V battery pack can be used on 54V & 18V

Black+Decker Cordless tools. The battery can recognise

the tool it is inserted into and will run at the relevant power,

providing longer runtime in 18V tools. There is a State of

charge button (11) which will indicate the level charge at both

54V & 18V

Operation

u To turn the unit on, push the lock off button (2) down,

squeeze the trigger (1) and depress the dual switch bail

handle(6), as shown in gure G. Once the unit is running,

you may release the lock-off button. In order to keep the

unit running you must continue to squeeze the trigger.

Warning! Never attempt to lock a switch in the on position.

Trimming Instructions

u Maintain proper footing and balance and do not overreach.

Wear safety goggles, non-skid footwear when trimming.

Hold the unit rmly in both hands and turn the unit ON.

Always hold the trimmer, as shown in the illustrations in

this manual, with one hand on the switch handle and one

hand on the bail handle (gureG). Never hold the unit by

the blade guard.

Trimming new growth (Fig. H)

u A wide, sweeping motion, feeding the blade teeth through

the twigs is most effective. A slight downward tilt of the

blade, in the direction of motion gives the best cutting.

Warning! Do not cut stems greater than 19mm. Use the

trimmer only for cutting normal shrubbery around houses and

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Black and Decker GTC5455PCB Pensasleikkuri. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Black and Decker. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Black and Decker GTC5455PCB Pensasleikkuri käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Black and Decker Pensasleikkurit
Lisää Pensasleikkurit käsikirjoja

Usein kysytyt kysymykset kohteesta Black and Decker GTC5455PCB Pensasleikkuri

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Black and Decker GT534 Pensasleikkuri

Käyttöohje

Black and Decker GTC3655L Pensasleikkuri

Käyttöohje

Black and Decker GTC1850L Pensasleikkuri

Käyttöohje

Black and Decker GTC36552PC Pensasleikkuri

Käyttöohje

Black and Decker GTC18452PC Pensasleikkuri

Käyttöohje

Black and Decker GT430 Pensasleikkuri

Käyttöohje

Black and Decker MT18SSK Pensasleikkuri

Käyttöohje

Black and Decker GTC2451 Pensasleikkuri

Aiheeseen liittyvät luokat