Käyttöohje Black and Decker GTC5455PCB Pensasleikkuri

Käyttöohje

9

ENGLISH

(Original instructions)

buildings.

Level hedges (Fig. I)

u To obtain exceptionally level hedges a piece of string can

be stretched along the length of the hedge as a guide.

Side trimming hedges (Fig. J)

u Hold the trimmer as shown and begin at the bottom and

sweep up.

POWERCOMMAND (Fig.K)

If you encounter a jam, depress the POWERCOMMAND

button (4) shown in gure K. The blades will move back and

forth in a slower, more forceful rhythm to help cut through dif-

cult branches. Release the button to return to normal hedge

trimming usage.

Note: Once the button is released, the blades will immediately

return to full speed.

Note: The blades will stop when the button is held for 15 sec-

onds. To reengage the POWERCOMMAND feature, release

the button and depress it again. DO NOT continuously hold

the POWERCOMMAND button during normal hedge trimming.

Saw blade (Fig.L)

For branches too large for the blade ( 7 ) to cut, use the saw

blade (8 ). Position the saw blade as close to the bottom of the

branch as possible. Place the saw blade shoe ( 9 ) against the

branch. Turn the hedge trimmer on as described above, allow-

ing the tool to work at its own pace until the branch is fully cut.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u After use, carefully clean the blades. After cleaning, apply

a lm of light machine oil to prevent the blades from rust-

ing.

The cutting blades are made from high quality, hardened steel

and with normal usage, they will not require resharpening.

However, if you accidentally hit a wire fence, stones, glass or

other hard objects, you may put a nick in the blade.

There is no need to remove this nick as long as it does not

interfere with the movement of the blade. If it does interfere,

remove the battery and use a ne toothed le or sharpening

stone to remove the nick.

If you drop the trimmer, carefully inspect it for damage. If the

blade is bent, housing cracked, or handles broken or if you

see any other condition that may affect the trimmer’s opera-

tion contact your local BLACK+DECKER Service Center for

repairs before putting it back into use. Fertilizers and other

garden chemicals contain agents which greatly accelerate

the corrosion of metals. Do not store the unit on or adjacent

to fertilizers or chemicals. With the battery removed, use only

mild soap and a damp cloth to clean the unit. Never let any

liquid get inside the unit; never immerse any part of the unit

into a liquid. Prevent the blades from rusting by applying a lm

of light machine oil after cleaning.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Troubleshooting

Problem Possible Cause Possible Solution

Slow running,

noisy or hot

blades.

Dry, corroded blades. Lubricate blades.

Blade or blade sup-

port bent.

Straighten blade or blade support.

Bent or damaged

teeth.

Straighten teeth.

Loose blade bolts. Tighten blade bolts.

Unit will not

start.

Battery not installed

properly.

Check battery installation.

Battery not charged. Check battery charging require-

ments.

Lock off not fully

operated.

Check lock off is fully depressed

prior to moving main trigger.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Black and Decker GTC5455PCB Pensasleikkuri. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Black and Decker. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Black and Decker GTC5455PCB Pensasleikkuri käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Black and Decker Pensasleikkurit
Lisää Pensasleikkurit käsikirjoja

Usein kysytyt kysymykset kohteesta Black and Decker GTC5455PCB Pensasleikkuri

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Black and Decker GT534 Pensasleikkuri

Käyttöohje

Black and Decker GTC3655L Pensasleikkuri

Käyttöohje

Black and Decker GTC1850L Pensasleikkuri

Käyttöohje

Black and Decker GTC36552PC Pensasleikkuri

Käyttöohje

Black and Decker GTC18452PC Pensasleikkuri

Käyttöohje

Black and Decker GT430 Pensasleikkuri

Käyttöohje

Black and Decker MT18SSK Pensasleikkuri

Käyttöohje

Black and Decker GTC2451 Pensasleikkuri

Aiheeseen liittyvät luokat