Käyttöohje Siemens TS20XTRM Silitysrauta

Käyttöohje

14

en

Trouble shooting

Problem Possible causes Solution

The steam generator

does not come on.

• There is a connection problem.

• The main power button is not

switched on.

• Check the mains cable, the plug and the

socket.

• Set the main power button (12) to the “I”

position.

The iron does not

heat up.

• The main power button is not

switched on.

• The temperature control knob is set

to the “min” position.

• Set the main power button (12) to the “I”

position.

• Set the temperature control knob (14) to

the desired position.

The iron begins to

smoke when switched

on.

• During first use: Certain components

on the appliance have been lightly

greased at the factory and may

produce a little smoke when initially

heated.

• During later use: the soleplate may

be soiled.

• This is completely normal and will stop

after a short while.

• Clean the soleplate according to the

cleaning instructions in this manual.

Water flows through

the holes on the sole

plate.

• The steam function is being used

before it has reached temperature.

• The water is condensing inside the

pipes because steam is being used

for the first time or has not been used

for a long time.

• Reduce the steam flow when ironing at

low temperatures (Variable steam control

(10)).

• Point the iron away from the ironing area

and press the steam release button until

steam is produced.

“Calc‘n clean” (F)

Cleaning the Boiler

To extend the life of your steam generator and to To

extend the life of your steam generator and to avoid

any build up of scale, it is essential that you rinse out

the boiler after several hours of use (approximately after

50 hours). If the water is hard, increase the frequency.

Do not use descaling agents for rinsing out the boiler,

as they could damage it.

1. Check that the appliance is cold and unplugged for

more than 2 hours, and that the water tank (1) is

empty.

2. Place your appliance on the edge of your kitchen

sink.

3. Remove the plastic cover located on the bottom of

the appliance by turning it to the position.

4. Unscrew the boiler drainage plug using a coin.

5. Holding your steam generator in upside down

position, and using a jug, fill the boiler (in the base

unit) with 1/4 litre of water

6. Shake the base unit for a few moments and then

empty it completely over a sink or bucket. To obtain

the best result, we recommend that this operation is

done twice.

Important: before re-closing, make sure no water

remains in the boiler.

7. Replace and tighten up the boiler drainage plug with

a coin.

8. Insert and close the plastic cover by turning it to the

position.

Rinsing the iron steam chamber (G)

Caution! Risk of burns!

This procedure helps to remove scale particles out of

the steam chamber.

Carry it out approximately every 2 weeks, if the water

in your area is very hard.

a) Ensure that the iron is cooled down.

b) Set the temperature selector (14) of the iron to the

“min” position.

c) Fill the tank with tap water.

d) Plug in the mains cable and set the main power

switch (12) to the “I” position.

e) Wait until the “steam ready” indicator lamp (9) lights

up.

f) If the steam station has steam regulator (10), set it to

the maximum position .

g) Hold the iron over the sink or a container to collect

the water.

h) Press the steam release button (15) and gently

shake the iron. Boiling water and steam will come

out, carrying scale and or deposits that might be

there. This could take approximately 5 minutes.

i) Set the temperature selector (14) of the iron to the

“max” position, without pressing the steam release

button (15). The water in the steam chamber will

start evaporating. Wait until all the water inside the

chamber has been evaporated.

j) To clean the soleplate, immediately rub off any

residue by running the hot iron over dry cotton

cloth.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Siemens TS20XTRM Silitysrauta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Siemens. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Siemens TS20XTRM Silitysrauta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Siemens Silitysraudat
Lisää Silitysraudat käsikirjoja

Usein kysytyt kysymykset kohteesta Siemens TS20XTRM Silitysrauta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Siemens TS203100X Silitysrauta

Käyttöohje

Siemens TB21573 Silitysrauta

Käyttöohje

Siemens TS11XTRM24 Silitysrauta

Käyttöohje

Siemens TB24305 Silitysrauta

Käyttöohje

Siemens TS25320 Silitysrauta

Käyttöohje

Siemens TS11XTRM Silitysrauta

Käyttöohje

Siemens TB24420 Silitysrauta

Käyttöohje

Siemens TS22XTRM Silitysrauta

Aiheeseen liittyvät luokat