Käyttöohje Philips GC1980 Silitysrauta

Käyttöohje

9 After you have used the Calc-Clean function, press down the steam

control while you turn it to position O. (Fig. 17)

Note: Repeat the Calc-Clean process if the water that comes out of the iron still

contains scale particles.

After the Calc-Clean process

1 Put the plug in the wall socket and let the iron heat up to let the

soleplate dry.

2 Unplug the iron when the temperature light goes out.

3 Move the iron gently over a piece of used cloth to remove any water

stains that may have formed on the soleplate.

4 Let the iron cool down before you store it.

Cleaning the steam control needle

1 Pull the steam control out of the appliance. (Fig. 18)

2 Use vinegar to remove scale, if any, from the needle (Fig. 19).

Do not bend or damage the steam control needle.

3 Reinsert the steam control. Place the point of the needle exactly in

thecentreoftheholeandtthesmallprojectiononthesideofthe

needle into the slot (Fig. 20).

4 Set the steam control to position O.

Storage

1 Set the steam control to position O and remove the plug from the

wall socket.

2 Wind the mains cord round the cord storage facility (Fig. 21).

3 Specictypesonly:puttheironintheheat-resistantstoragecover

and fasten the cover with the Velcro strips (Fig. 22).

Note: If you use the heat-resistant soleplate cover, you do not have to let the

iron cool down rst. If you want to store the iron without the soleplate cover,

let it cool down rst.

Environment

- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment (Fig. 23).

Guarantee and service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

guarantee leaet). If there is no Consumer Care Centre in your country,

go to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could encounter

with the appliance. If you are unable to solve the problem with the

information below, contact the Consumer Care Centre in your country.

Problem Possible cause Solution

The iron is

plugged in, but

the soleplate is

cold.

There is a

connection problem.

Check the mains cord, the plug

and the wall socket.

The temperature

dial is set to MIN.

Set the temperature dial to the

required position.

The iron does

not produce

any steam.

There is not enough

water in the water

tank.

Fill the water tank (see chapter

‘Using the appliance’, section

‘Filling the water tank’).

The steam control is

set to position O.

Set the steam control to the

small cloud or large cloud

(see chapter ‘Using the

appliance, section ‘Selecting

temperature and steam setting’).

The steam

boost function

does not

work properly

(specic types

only).

You have used

the steam boost

function too often

within a very short

period.

Put the iron on its heel or

continue ironing in horizontal

position and wait a while

before you use the steam boost

function again.

Steam boost function (specic types only)

A powerful boost of steam helps to remove very stubborn creases.

The steam boost function only works at temperature settings between

3 and MAX.

1 Press and release the steam boost button (Fig. 9).

Vertical shot of steam (specic types only)

You can also use the steam boost function when you hold the iron in

vertical position. This is useful for removing creases from hanging clothes,

curtains etc.

1 Hold the iron in vertical position and press and release the steam

boost button (Fig. 10).

Never direct the steam at people.

Automatic shut-off function (specic types only)

The automatic shut-off function automatically switches off the iron if it has

not been moved for a while.

, Theautomaticshut-offlightashestoindicatethattheironhasbeen

switched off by the automatic shut-off function (Fig. 11).

To let the iron heat up again:

1 Pick up the iron or move it slightly.

, Theautomaticshut-offlightstopsashing.

, If the temperature of the soleplate has dropped below the set ironing

temperature, the temperature light goes on.

2 If the temperature light goes on after you have moved the iron,

wait for it to go out before you start ironing.

Note: If the temperature light does not go on after you move the iron, the

soleplate still has the right temperature and the iron is ready for use.

Cleaning and maintenance

Cleaning

1 Set the steam control to position O, remove the plug from the wall

socket and let the iron cool down.

2 Pour any remaining water out of the water tank.

3 Wipeakesandanyotherdepositsoffthesoleplatewithadamp

cloth and a non-abrasive (liquid) cleaning agent.

Tokeepthesoleplatesmooth,avoidhardcontactwithmetalobjects.

Never use a scouring pad, vinegar or other chemicals to clean the

soleplate.

4 Clean the upper part of the iron with a damp cloth.

5 Regularly rinse the water tank with water. Empty the water tank after

you have rinsed it (Fig. 12).

Double-Active Calc System (specic types only)

Note: See chapter ‘General description’ for the type numbers that are equipped

with the Double-Active Calc System.

The Double-Active Calc System consists of an Anti-Calc tablet inside the

water tank combined with the Calc-Clean function.

- The Anti-Calc tablet prevents scale from clogging the steam vents. The

tablet is constantly active and does not need to be replaced (Fig. 13).

- The Calc-Clean function removes scale particles from the iron.

Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your

area is very hard (i.e. when akes come out of the soleplate during ironing),

use the Calc-Clean function more frequently.

1 Make sure the appliance is unplugged.

2 Set the steam control to position O.

3 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the water tank.

4 Set the temperature dial to MAX (Fig. 14).

5 Put the mains plug in an earthed wall socket.

6 Unplug the iron when the temperature light goes out.

7 Hold the iron over the sink and turn the steam control to the

Calc-Clean position x. (Fig. 15)

8 Pull the steam control slightly upwards and gently shake the iron until

all water in the tank has been used up (Fig. 16).

, Steam and boiling water come out of the soleplate. Scale (if any)

isushedout.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Philips GC1980 Silitysrauta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Philips. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Philips GC1980 Silitysrauta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Philips Silitysraudat
Lisää Silitysraudat käsikirjoja

Usein kysytyt kysymykset kohteesta Philips GC1980 Silitysrauta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Philips GC7011 Silitysrauta

Käyttöohje

Philips GC7220 Silitysrauta

Käyttöohje

Philips GC8703 Silitysrauta

Käyttöohje

Philips GC4238 Silitysrauta

Käyttöohje

Philips GC8962 Silitysrauta

Käyttöohje

Philips PSG6066 PerfectCare Silitysrauta

Käyttöohje

Philips GC6707 Silitysrauta

Käyttöohje

Philips GC7057 Silitysrauta

Aiheeseen liittyvät luokat