Käyttöohje Hozelock 1760 EasyClear 3000 Suihkulähdepumppu

Käyttöohje

disposed of according to local regulations.

1.11 A 30mA maximum Residual Current Device

(RCD) MUST be fitted to the mains supply.

1.12 Permanent installations to the mains supply

(hard wiring), must conform to the national and

local wiring regulations. If in any doubt about

wiring to the mains supply, consult a qualified

electrician or local electricity authority.

1.13 Do not use the supply cable to lift the unit, as

this may cause damage. We recommend fitting

a lifting cord to the hook feature on the base,

when the filter is installed in deep water. (Fig

1-H). If the product needs to be moved, the

product should be switched off and lifted out of

the water using this cord.

1.14 Do not switch the pump on out of water! The

water level should be above the UVC indicator at

the ball joint (Fig 4A-L).

1.15 Do not operate or leave the unit in freezing

conditions. (See the section, “Winter Storage”).

1.16 This product is not suitable for water

temperatures above 35ºC or below 0ºC.

1.17 Only use accessories which have been designed

for use with this product. The use of any other

accessories or spares may invalidate your

guarantee.

Overload Protection

To help ensure your EasyClear’s long life and to

prevent damage, it is fitted with automatic thermal

overload protection. This switches the pump or UV

lamp off if either overheats. If this occurs, switch off

the power at the mains supply to the unit. If it is the

pump that has activated the Overload Protection,

check for the cause (it is usually debris blocking the

inlet of the pump or obstructing the impeller). Remove

the obstruction and wait 15 minutes for the unit to

cool down. Then switch it on again.

If it is the UV lamp that is activating the overload

protection (pump is still running but UV lamp keeps

going out after running for a short time), please

contact Hozelock Consumer Services Helpline on +44

(0)121 313 1122.

Remember: The lamp is fitted with an interlock that

will turn the lamp off when the bayonet is removed

(fig 8-S), so you can only see if the lamp is working in

dark conditions, by looking for a bluish glow from the

Fountain outlet (Fig 1-A) with the bayonet tube locked

in position.

NOTE: YOU MUST SWITCH OFF THE MAINS

SUPPLY BEFORE THE UNIT WILL RESET.

CAUTION: To avoid a safety hazard due to inadvertent

resetting of the thermal overload protection, this

product must not be used with an external switching

device, such as a timer, or connected to a circuit that is

regularly switched on and off by the electricity supply.

Periods of Operation

Keep the filter working 24 hours a day. Ideally it

should run all year round, but at least throughout the

fish-feeding season, (i.e. until the water temperature

falls below 10°C and the fish stop feeding). In winter,

operating the unit will maintain a basic level of useful

bacteria in the Biological Filter, and will help prevent

the pond icing over. However, the unit must not be

allowed to freeze. If you switch the unit off for winter,

wash the unit thoroughly before resuming filtration in

the spring (see ‘Winter Storage’). Never feed your fish

when the unit is not in use.

Before First Use

Inappropriate handling of this product during transit

may result in damage to the quartz tube. Please

inspect the quartz tube and seal before installation.

See the section “Maintenance” for details on how to

access the quartz tube and lamp.

Installation

Position - Construct a solid and level platform on

which to place the EasyClear™. The platform should be

greater than 300 mm (12”) below the water level. For

depths between 300mm and 600mm use the fountain

stem extension segments (Fig 1-F), which simply screw

together, to allow the fountain to be above the water



using the EasyClear for a waterfall the entire unit

should be submersed.

Connection - Place the unit next to the pond and

route the cable back to the mains supply. Ensure that

you allow for enough cable for positioning the product

in the desired location in the pond.

Accessory Assembly

Bell Fountain (Fig 1).

Locate the Bell Support (B) to the Bell Main Body (C)

and push fully home.

Position the Bell (D) to the Body Assembly and press

into the central location.

2 and 3 tier fountain display assembly (Fig 1-I).

The plastic discs (Fig 1-E) that create the 2 and 3

tier water displays simply snap onto the fountain

stem. Push the fountain stem into the fountain stem

extension segment and screw onto the fountain outlet

(Fig 1-A).

Fountain Only Operation

(Fig 4-A for general installation guide)

Please note: The product has a water by-pass to

control water flow rates which means a quantity

of water will always come out of the product just

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Hozelock 1760 EasyClear 3000 Suihkulähdepumppu. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Hozelock. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Hozelock 1760 EasyClear 3000 Suihkulähdepumppu käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Hozelock Suihkulähdepumput
Lisää Suihkulähdepumput käsikirjoja

Liittyvät tuotteet

Käyttöohje

Hozelock 1584A Aquaforce 8000 Suihkulähdepumppu

Käyttöohje

Hozelock 3354 Cascade 1500 Suihkulähdepumppu

Käyttöohje

Hozelock 1766 EasyClear 7500 Suihkulähdepumppu

Käyttöohje

Hozelock 1581 Aquaforce 2500 Suihkulähdepumppu

Käyttöohje

Hozelock 3303 Cascade 450 Suihkulähdepumppu

Käyttöohje

Hozelock 3334 Cascade 3000 Suihkulähdepumppu

Käyttöohje

Hozelock 1768 EasyClear 9000 Suihkulähdepumppu

Käyttöohje

Hozelock 3352 Cascade 700 Suihkulähdepumppu

Aiheeseen liittyvät luokat