Käyttöohje Hozelock 1760 EasyClear 3000 Suihkulähdepumppu

Käyttöohje

below the flow control. This is normal in operation.

Position the unit in the pond. The fountain angle can

be adjusted to be vertical using the ball joint (Fig 2-A).

The tightness of the ball joint can be adjusted (Fig 2-J).

If required, the 2-Tier Fountainhead can be used to

achieve an alternative and higher display pattern than

the 3-Tier.

The fountain height can be adjusted to suit your needs

by rotating the Fountain Flow Adjuster (Fig 3-K).

The Bell Fountain creates a decorative waterbell. The

size of the bell can be adjusted to suit your needs by

rotating the Fountain Flow Adjuster (Fig 3-K).

Waterfall Only Operation

(Fig 4-B for general installation guide)

Position the pump as previously described.

Attach a suitable length (3m maximum) of 25 mm (1”)

hose to the waterfall hose tail (Fig 1-G) and secure

with a suitable hose clip and position the outlet end of

the hose in the desired position.

Screw the waterfall hose tail to the fountain outlet of

the EasyClear™ (Fig 1-A) and adjust the flow using the

fountain flow adjuster, (Fig 3-K), to suit your needs.

Note: The maximum recommended waterfall height

above pond level is 0.5m (Fig 4-B).

UVC Operation

The UVC will automatically switch on once the unit

has been connected to the electricity supply if the

bayonet tube is correctly locked in place.

The UVC lamp can be checked for operation by

looking for a bluish glow from ball joint outlet (Fig

1-A). Please note that this may only become visible in

low light conditions.

See Maintenance section for Lamp replacement.

Maintenance

The Hozelock Cyprio EasyClear™ has been designed

to allow fast and easy maintenance. As with all pond

equipment, occasionally it will become necessary to

clean or replace parts.

WARNING: Disconnect this product from the

electricity supply and refer to the section “Safety

& Electrical Connections” before attempting any

maintenance.

Fountain Head (Fig 1-I)

Follow the below procedure if the fountain head is

blocked:

1 - Place a coin or similar in the slot and gently lever

off the fountain head.

2 - Rinse in clean water and reassemble.

Foam

Follow the below procedure if flow appears reduced:

1 - Release the Foam Cover by pushing the two

buttons (Fig 5-M) and lift the cover (Fig 6-N).

2 - Remove the Foam (Fig 7-O). Note:- If the unit is

out of the pond for more then 20 minutes the

biological filter action may stop working. Rinse

thoroughly in pond water (do not use tap water).

3 - The Foam Cover and Base should also be rinsed in

pond water (do not use tap water).

4 - It may also be necessary to clean out the

biomedia and stones (Fig 7-P) if these have

become clogged. If this is necessary, the biomedia

and stones should be rinsed in pond water only.

5 - Reassemble the Filter.

Quartz Tube

Follow the below procedure if your pond remains

green:

1 - Remove the bayonet locking screw (Fig 8-Q), twist

and lift the bayonet tube (Fig 8-R).

2 - Clean the Quartz Tube. Take extra care when

handling the Quartz tube. In hard water areas,

the quartz tube may become covered in limescale,

which will reduce efficiency. Clean the tube with a

soft cloth and a gentle de-scaler (such as vinegar

and water), rinse in water before refitting.

3 - Reassemble the bayonet tube and screw and

restart (Fig 8-S).

Warning! Ensure that the quartz tube is not

damaged before refitting.

Lamp Replacement

Follow the below procedure if the lamp needs

replacing or does not illuminate:

Change the lamp at the start of the new season. Even

though the lamp still glows it may not be giving out

anyuseful UV radiation. How well the EasyClear™

performs is related to the strength of the UV radiation

produced. This will slowly decline from the day your

lamp is switched on. The UVC lamp has an effective



there is a significant reduction in water clarity. Make

sure this is due to an expired lamp and not a badly



Both can greatly reduce UV transmission into the

water.

1 - Remove the bayonet locking screw (Fig 8-Q), twist

and lift the bayonet tube (Fig 8-R).

2 - Unscrew the quartz tube locking collar (Fig 9-T-i).

Gently hold the quartz tube (Fig 9-T-ii), lift up and

remove together with its o-rings (Fig 9-T-iii) and

locking collar.

3 - Remove the old lamp by gently pulling it from

its holder (Fig 9-U). Dispose of the old lamp

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Hozelock 1760 EasyClear 3000 Suihkulähdepumppu. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Hozelock. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Hozelock 1760 EasyClear 3000 Suihkulähdepumppu käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Hozelock Suihkulähdepumput
Lisää Suihkulähdepumput käsikirjoja

Liittyvät tuotteet

Käyttöohje

Hozelock 1584A Aquaforce 8000 Suihkulähdepumppu

Käyttöohje

Hozelock 3354 Cascade 1500 Suihkulähdepumppu

Käyttöohje

Hozelock 1766 EasyClear 7500 Suihkulähdepumppu

Käyttöohje

Hozelock 1581 Aquaforce 2500 Suihkulähdepumppu

Käyttöohje

Hozelock 3303 Cascade 450 Suihkulähdepumppu

Käyttöohje

Hozelock 3334 Cascade 3000 Suihkulähdepumppu

Käyttöohje

Hozelock 1768 EasyClear 9000 Suihkulähdepumppu

Käyttöohje

Hozelock 3352 Cascade 700 Suihkulähdepumppu

Aiheeseen liittyvät luokat