Käyttöohje Black and Decker VPX1101 Ruuvitaltta

Käyttöohje

6

ENGLISH

X The charging indicator (9) will be lit as long as the

battery pack is connected to the plugged-in charger.

X Charge discharged batteries within 1 week. Battery life

will be greatly diminished if stored in a discharged state.

Charge indicators

If the charger detects a problem with a battery pack, the

charge indicator (9) will flash at a fast rate.

X If this occurs, re-insert the battery pack (7).

X If the problem persists, put a different battery pack in the

charger to determine if the charger is OK.

X If the new battery pack charges correctly, then the

original battery pack is defective and should be returned

to a service centre for recycling.

X If the new battery pack gives the same indication as the

original, take the charger to be tested at an authorized

service centre.

Note: It may take as long as fifteen minutes to determine that

the pack is defective.

If the battery pack is too hot or too cold, the LED will

alternately blink fast and slow, one flash at each speed and

repeat.

Battery chargers - daisy chaining (fig. C)

Single and dual port chargers can be electrically connected

in any order up to a maximum of 4 chargers. Each charger

has a power-in cord (10) which plugs into the electrical outlet

and a power-out cord (11) which plugs into the next charger.

To connect the chargers in a daisy chain:

X Plug the power-in cord (10) into an electrical outlet.

X Remove the power-in cord from the next charger and

plug in the power-out cord (11) rom the charger that is

now plugged into the outlet.

X Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate

independently as though each one was plugged into a

separate outlet, therefore a battery can be removed from

anywhere along the daisy chain without affecting the other

chargers.

Use

Switching on and off (fig. D)

X To switch the tool on, press the on/off trigger switch (6).

X To switch the tool off, release the on/off trigger

switch (6).

X A forward/reverse control button (3) determines the

direction of the tool and also serves as a lock off button.

X To select forward rotation, release the on/off trigger

switch (6) and move the forward/reverse control button

(3) to the left.

X To select reverse direction, move the forward/reverse

control button (3) in the opposite direction.

X The centre position of the control button (3) locks the

tool in the off position. Make sure that the on/off trigger

switch (6) is released before changing the position of

the forward/reverse control button (3).

High/low speed selector (fig. D)

The 2-speed feature of your screwdriver allows for greater

versatility.

X To select the low speed, high torque setting (position 1),

turn the tool off and allow it to stop. Move the speed

selector switch (2) to the right.

X To select the high speed, low torque setting (position 2),

turn the tool off and allow it to stop. Move the speed

selector switch (2) to the left.

Warning! Do not move the speed selector button with the

tool switched on.

Quick release collar (fig. E)

Note: The collar accepts 1/4" hex accessories only.

To install a screwdriver bit or other accessory, pull the collar

(1) back and insert the bit into the collar until it locks into

place.

To remove a screwdriver bit or other accessory, pull the

collar (1) back. Remove the bit and release the collar.

Driving screws

X When driving screws, the forward/reverse button (3)

should be pushed to the left.

X Move the forward/reverse button (3) pushed to the right

for removing screws.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

X Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

X Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

X Regularly open the chuck and tap it to remove any dust

from the interior.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Black and Decker VPX1101 Ruuvitaltta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Black and Decker. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Black and Decker VPX1101 Ruuvitaltta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Black and Decker Ruuvitaltat
Lisää Ruuvitaltat käsikirjoja

Usein kysytyt kysymykset kohteesta Black and Decker VPX1101 Ruuvitaltta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Black and Decker KC9006 Ruuvitaltta

Käyttöohje

Black and Decker PP360 Ruuvitaltta

Käyttöohje

Black and Decker AS36LN Ruuvitaltta

Käyttöohje

Black and Decker KC9024 Ruuvitaltta

Käyttöohje

Black and Decker BCF602 Ruuvitaltta

Käyttöohje

Black and Decker KC460LN Ruuvitaltta

Käyttöohje

Black and Decker KC1036 Ruuvitaltta

Käyttöohje

Black and Decker HP9096 Ruuvitaltta

Aiheeseen liittyvät luokat