Käyttöohje Biltema 24-626 Autoradio

Käyttöohje

Art. 24-626

© 2015-02-03 Biltema Nordic Services AB

3

Frontmontering (metod A)

Denna enhet kan frontmonteras i alla instru-

mentbrädor som har en öppning enligt bilden

nedan:

Försäkra dig först om att alla anslutningar är

korrekt utförda och följ sedan följande steg:

1. Kontrollera att tändningen är avslagen och

koppla loss bilbatteriets minuspol.

2. Koppla loss kabelhärvan och antennen

från enheten.

3

INSTALLATION

Notes:

 Choose the mounting location where

the unit will not interfere with the

normal driving function of the driver.

 Before finally installing the unit, connect

the wiring temporarily and make sure it

is all connected up properly and the

unit and the system work properly.

 Use only the parts included with the

unit to ensure proper installation. The

use of unauthorized parts can cause

malfunctions.

 Consult with your nearest dealer if

installation requires the drilling of holes

or other modifications of the vehicle.

 Install the unit where it does not get in

the driver’s way and cannot injure the

passenger if there is a sudden stop, like

an emergency stop.

 If installation angel exceeds 30°from

horizontal, the unit might not give its

optimum performance.

 Avoid installing the unit where it would

be subject to high temperature, such as

from direct sunlight, or from hot air,

from the heater, or where it would be

subject to dust, dirt or excessive

vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either

from “Front” (conventional DIN Front-mount)

or “Rear” (DIN Rear-mount installation,

utilizing threaded screw holes at the sides

of the unit chassis). For details, refer to the

following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation Opening

This unit can be installed in any dashboard

having an opening as shown below:

Installing the unit

Be sure you test all connections first, and

then follow these steps to install the unit.

1. Make sure the ignition is turned off, and

then disconnect the cable from the

vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the

antenna.

3. Press the release button on the front

panel and remove the control panel

(see the steps of “removing the front

panel”).

4. Lift the top of the outer trim ring then pull

it out to remove it.

5. The two supplied keys release tabs

inside the unit’s sleeve so you can

remove it. Insert the keys as far as

they will go (with the notches facing up)

into the appropriate slots at the middle

left and right sides of the unit. Then slide

the sleeve off the back of the unit.

30

Outer Trim Ring

Front Panel

L Key

Sleeve

R Key

53mm

182mm

3

INSTALLATION

Notes:

 Choose the mounting location where

the unit will not interfere with the

normal driving function of the driver.

 Before finally installing the unit, connect

the wiring temporarily and make sure it

is all connected up properly and the

unit and the system work properly.

 Use only the parts included with the

unit to ensure proper installation. The

use of unauthorized parts can cause

malfunctions.

 Consult with your nearest dealer if

installation requires the drilling of holes

or other modifications of the vehicle.

 Install the unit where it does not get in

the driver’s way and cannot injure the

passenger if there is a sudden stop, like

an emergency stop.

 If installation angel exceeds 30°from

horizontal, the unit might not give its

optimum performance.

 Avoid installing the unit where it would

be subject to high temperature, such as

from direct sunlight, or from hot air,

from the heater, or where it would be

subject to dust, dirt or excessive

vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either

from “Front” (conventional DIN Front-mount)

or “Rear” (DIN Rear-mount installation,

utilizing threaded screw holes at the sides

of the unit chassis). For details, refer to the

following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation Opening

This unit can be installed in any dashboard

having an opening as shown below:

Installing the unit

Be sure you test all connections first, and

then follow these steps to install the unit.

1. Make sure the ignition is turned off, and

then disconnect the cable from the

vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the

antenna.

3. Press the release button on the front

panel and remove the control panel

(see the steps of “removing the front

panel”).

4. Lift the top of the outer trim ring then pull

it out to remove it.

5. The two supplied keys release tabs

inside the unit’s sleeve so you can

remove it. Insert the keys as far as

they will go (with the notches facing up)

into the appropriate slots at the middle

left and right sides of the unit. Then slide

the sleeve off the back of the unit.

30

Outer Trim Ring

Front Panel

L Key

Sleeve

R Key

53mm

182mm

5. Höger nyckel

1. Frontpanel

2. Sarg

3. Hölje

4. Vänster nyckel

4

INSTALLATION

6. Mount the sleeve by inserting the sleeve

into the opening of the dashboard and

bend open the tabs located around the

sleeve with a screwdriver. Not all tabs

will be able to make contact, so

examine which ones will be most

effective. Bending open the appropriate

tabs behind the dashboard to secure

the sleeve in place.

Tabs

Screwdriver

Sleeve

Dashboard

7. Reconnect the wire harness and the

antenna and be careful not to pinch any

wires or cables.

8. Slide the unit into the sleeve until it

locks into place.

9. To further secure the unit, use the

supplied metal strap to secure the

back of the unit in place. Use the

supplied hardware (Hex Nut (M5mm)

and Spring Washer) to attach one end of

the strap to the mounting bolt on the back

of the unit. If necessary, bend the metal

strap to fit your vehicle’s mounting area.

Then use the supplied hardware

(Tapping Screw (5x25mm) and Plain

Washer) to attach the other end of metal

strap to a solid metal part of the vehicle

under the dashboard. This strap also

helps ensure proper electrical grounding

of the unit.

Note to install the short threading

terminal of the mounting bolt to the back

of the unit and the other long threading

terminal to the dashboard.

Mounting Bolt

Spring Washer

Plain Washer

Tapping Screw

Hex Nut

Metal Strap

10. Reconnect the cable to the vehicle

battery’s negative (-) terminal. Then

replace the outer trim ring and install the

unit’s front panel (see the steps of

“installing the front panel”).

Removing the unit

1. Make sure the ignition is turned off, then

disconnect the cable from the vehicle

battery’s negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

3. Press the release button to remove the

front panel.

4. Lift the top of the outer trim ring then pull

it out to remove it.

5. Insert both of the supplied keys into the

slots at the middle left and right sides of

the unit, then pull the unit out of the

dashboard.

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan, Toyota, follow

these mounting instructions.Use the screw

holes marked T (Toyota), N (Nissan)

located on both sides of the unit to

1. Instrumentbräda

2. Flik/spärr

3. Skruvmejsel

4. Hölje

3. Tryck på frontpanelens releaseknapp och

lossapanelen(förnärmaredetaljer,se

avsnittet ’Att använda den löstagbara front-

panelen’).

4. Tatagitoppsidanavsargen,lyftdenförsik-

tigt uppåt och drag sedan utåt för att lossa

den.

5. De två medföljande metallnycklarna an-

vänds för att lossa enheten från höljet. För

innycklarna,medmärkningenpekande

uppåt,idesmalahålsomnnsimittenav

höljets höger och vänsterkanter (se illustra-

tion). Genom att trycka in nycklarna så los-

sar du de två metallspärrar som håller fast

höljet.Lossahöljetgenomatttryckadet

bakåt med hjälp av nycklarna.

6. Montera höljet genom att försiktigt passa in

det i instrumentbrädans öppning och böj ut

metallikarna med en skruvmejsel. Troligen

kommer inte alla ikar att vara användbara

förattlåsahöljet,såkontrolleravilkaikar

som lämpar sig bäst och säkra höljet med

hjälp av dessa.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Biltema 24-626 Autoradio. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Biltema. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Biltema 24-626 Autoradio käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Biltema Autoradiot
Lisää Autoradiot käsikirjoja

Usein kysytyt kysymykset kohteesta Biltema 24-626 Autoradio

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Biltema 24-686 Autoradio

Käyttöohje

Biltema 24-624 Autoradio

Käyttöohje

Biltema 24-669 Autoradio

Käyttöohje

Biltema 24-6771 Autoradio

Käyttöohje

Biltema 24-665 Autoradio

Käyttöohje

Biltema 24-666 Autoradio

Käyttöohje

Biltema 24-604 Autoradio

Käyttöohje

JVC KD-T922BT Autoradio

Aiheeseen liittyvät luokat