10
- empty dust bag regularly for optimal dust pick-up
performance
• On/o switch
- switch on/o the tool by pushing switch F
2
forward/
backwards
! before the sanding surface reaches the workpiece,
you should switch on the tool
!
the workpiece
• Holding and guiding the tool
w
! while working, always hold the tool at the grey-
coloured grip area(s)
- guide the tool parallel to the working surface
- do not apply too much pressure on the tool; let the
sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots H
2
uncovered
APPLICATION ADVICE
• Use the tool with its standard foot plate for sanding large
surfaces, corners and edges
e
• Use the tool with the special sanding attachments for
hard-to-reach places
r
• The exible sanding attachment is intended for
- rounding edged surfaces
t
a
- all rounded surfaces with a maximum diameter of 10
cm
t
b
• When the delta-tip is worn or damaged at the top, you
may extend its service life twice by removing it, turning it
120° and putting it back (also applicable to delta sanding
sheet)
y
Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
- for removing paint and for sanding of extremely rough
wood use coarse grit sizes (40, 60)
- for sanding of rough or plain wood use medium grit
sizes (80, 100, 120)
- for smoothing of wood and surfaces with old paint as
well as for nishing of bare wood use ne grit sizes
(180, 240, 320)
• Use dierent grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- nish with ne grit
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H
2
)
- remove adhering sanding dust with a brush
- remove battery from tool before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3
Read the instruction manual before use
4
Batteries may explode when disposed of in re, so do not
burn battery for any reason
5
Store tool/charger/battery in locations where temperature
will not exceed 50°C
6
Do not dispose of electric tools and batteries together
with household waste material
USE
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery
2
• Battery level indicator
7
- press the battery level indicator button J to show the
current battery level
7
a
! when the lowest level of the battery indicator
7
b, the
battery is empty
!
after pressing button J
7
c, the battery is not
within the allowable operating temperature range
• Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button J
7
c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level
7
b is shown by the battery level indicator
when pressing button J; charge battery
!
damaged
• Mounting of sanding sheet
8
! remove battery from tool before making any
adjustments or changing accessories
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total sanding surface
covered with sanding paper
- mount VELCRO sanding sheet as illustrated
• Mounting special sanding attachments (not standard
included)
9
- remove VELCRO sanding sheet
- remove delta tip A while pushing button B
- mount desired sanding attachment as illustrated
- mount corresponding VELCRO sanding sheet to
sanding attachment
• Dust suction
! do not use dust bag when sanding metal
Dust bag
q
- mount dust bag D
Keskustele tuotteesta
Täällä voit jakaa mielipiteesi Skil 3720 CD Kärkihiomakone:sta. Jos sinulla on kysyttävää, lue ensin huolellisesti käyttöohje. Käsikirjaa voi pyytää yhteydenottolomakkeellamme.