Käyttöohje Skil 3008 HC Porakone-ruuvinväännin

Käyttöohje

10

• Changing direction of rotation

9

- when not properly set in left/right position, switch A

2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits

q

! do not use bits with a damaged shank

• Torque control (VariTorque)

w

- output torque will increase as clutch ring B is rotated

from 1 to 17; position C will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection

e

- set selector D to desired speed

! actuate the gear selector while tool is running

slowly

1

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

2

- high speed

- lower torque

- for impact drilling

- for drilling small diameters

• Holding and guiding the tool

t

! while working, always hold the tool at the grey-

coloured grip area(s)

- keep ventilation slots H

2

uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits

y

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• Splinterfree drilling in wood

u

• Dustfree drilling in walls

i

• Drilling in tiles without skidding

o

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots H

2

)

! remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

- SKIL battery: BR1*31****

- SKIL charger: CR1*31****

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

- when charging 4...40°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3

Read the instruction manual before use

4

Batteries may explode when disposed of in re, so do not

burn battery for any reason

5

Store tool/charger/battery in locations where temperature

will not exceed 50°C

6

Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A

2

- control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery

2

• Attaching belt clip

7

- attach the belt clip J to the drill with the supplied screw.

• Battery level indicator

8

- press the battery level indicator button K to show the

current battery level

8

a

! when the lowest level of the battery indicator



8

b, the

battery is empty

! 

after pressing button K

8

c, the battery is not

within the allowable operating temperature range

• LED-light

r

LED-light automatically lights on when activating the on/

o switch

! 

protection is activated (see below)

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

- the load is too high --> remove load and restart

- the battery temperature is not within the allowable

operating temperature range of -20 to +50°C --> 2

levels of the battery level indicator start ashing when

pressing button K

8

c; wait until battery has returned

within the allowable operating temperature range

- the battery is nearly empty (to protect against

deep discharge) --> a low battery level or ashing low

battery level

8

b is shown by the battery level indicator

when pressing button K; charge battery

! 



damaged

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Skil 3008 HC Porakone-ruuvinväännin. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Skil. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Skil 3008 HC Porakone-ruuvinväännin käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Skil Porakone-ruuvinvääntimet
Lisää Porakone-ruuvinvääntimet käsikirjoja

Usein kysytyt kysymykset kohteesta Skil 3008 HC Porakone-ruuvinväännin

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Skil 3085 HC Porakone-ruuvinväännin

Käyttöohje

Skil 3070 BA Porakone-ruuvinväännin

Käyttöohje

Skil 3085 CA Porakone-ruuvinväännin

Käyttöohje

Skil 3020 HE Porakone-ruuvinväännin

Käyttöohje

Skil 3018 HB Porakone-ruuvinväännin

Käyttöohje

Skil 3066 HC Porakone-ruuvinväännin

Käyttöohje

Skil 2070 CA Porakone-ruuvinväännin

Käyttöohje

Skil 3008 HE Porakone-ruuvinväännin

Aiheeseen liittyvät luokat