Käyttöohje Ryobi R18CSP-0 Pyörösaha

Käyttöohje

2 | English

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If the saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or any

other part, in all angles and depths of cut.

■ Check the operation of the lower guard spring. If

the guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

■ Lower guard may be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts”. Raise lower guard by retracting handle and

as soon as blade enters the material, the lower

guard must be released. For all other sawing, the

lower guard should operate automatically.

■ Always observe that the lower guard is covering the

blade before placing saw down on bench or floor.

An unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after

switch is released.

ADDITIONAL SAFETY WARNINGS

■ The dust produced when using the product may be

harmful to your health, inflammable, or explosive.

Do not inhale the dust. Use a dust extraction system,

and wear a suitable dust protection mask. Remove

deposited dust thoroughly, e.g., with a brush and

vacuum cleaner.

■ Do not use any abrasive wheels.

■ Use only blades specified in this manual, complying

with EN 847-1.

■ Avoid overheating the blade tips. Do not use dull or

damaged blades. Do not force the tool.

■ Do not use blades of larger or smaller diameter than

recommended.

■ Wear ear protection.

■ Clamp workpiece with a clamping device.

Unclamped workpieces can cause severe injury and

damage.

■ Thoroughly check the material to be cut, particularly

when using recycled wood, for foreign objects such

as nails, screws, and staples. If nails, screws, staples

or similar items contact the blade whilst cutting, the saw

will be damaged and severe injury to the operator or

others may occur.

■ Do not touch the saw blade immediately after

sawing. The saw blade gets hot during sawing.

■ Use only blade diameter(s) in accordance with the

markings.

■ Identify the correct saw blade to be used for the material

to be cut.

■ Use only saw blades that are marked with a speed

equal or higher than the speed marked on the tool.

■ Use only saw blades recommended by the

manufacturer, which conform to EN 847-1, if intended

for wood and analogous materials.

■ Wear a dust mask.

■ Ambient temperature range for tool during operation is

between 0°C and 40°C.

■ Ambient temperature range for tool storage is between

0°C and 40°C.

■ The recommended ambient temperature range for the

charging system during charging is between 10°C and

38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING

To reduce the risk of re, personal injury, and product

damage due to a short circuit, never immerse your

tool, battery pack or charger in uid or allow a uid to

ow inside them. Corrosive or conductive uids, such

as seawater, certain industrial chemicals, and bleach

or bleach-containing products, etc., can cause a short

circuit.

■ Ambient temperature range for battery during use is

between 0°C and 40°C.

■ Ambient temperature range for battery storage is

between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps

or tape. Do not transport batteries that are cracked or

leaking. Check with the forwarding company for further

advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still

impossible to completely eliminate certain residual risk

factors. The following hazards may arise and the operator

should pay special attention to avoid the following:

■ Injury caused by kickback

– Read and understand the information in this manual.

■ Injury caused by vibration

– Limit exposure. See Risk Reduction.

■ Injury caused by dust

– Wear eye protection at all times. Wear appropriate

dust mask with suitable filters that can protect

against particles from the material being worked on.

Do not eat, drink, or smoke in the work area. Ensure

adequate ventilation.

■ Electric shock

– The blade may contact hidden wiring causing

parts of the product to become live. Always hold

the product by the designated handles and take

care when blind-cutting into walls and floors where

cables may be hidden.

NOTE: When working on walls, ceilings, or floors, take

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Ryobi R18CSP-0 Pyörösaha. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Ryobi. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Ryobi R18CSP-0 Pyörösaha käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Ryobi Pyörösahat
Lisää Pyörösahat käsikirjoja

Usein kysytyt kysymykset kohteesta Ryobi R18CSP-0 Pyörösaha

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Ryobi LTS180M Pyörösaha

Käyttöohje

Ryobi CW-1801 Pyörösaha

Käyttöohje

Ryobi RWS1250 Pyörösaha

Käyttöohje

Ryobi LSC-180 Pyörösaha

Käyttöohje

Ryobi RCT18C-0 Pyörösaha

Käyttöohje

Ryobi RWS1400 Pyörösaha

Käyttöohje

Ryobi RCS18X-0 Pyörösaha

Käyttöohje

Ryobi EWS1266 Pyörösaha

Aiheeseen liittyvät luokat