Käyttöohje Qazqa 97681 Plater Lamppu

Käyttöohje

Please study the instruction manual and below information carefully before installing or using

1. The luminaires may only be installed by authorized and qualified technicians according the valid

regulations for electrical installation.

2. Maintenance of the luminaires is limited to their surfaces. During maintenance no moisture can come

into contact with any areas of the terminal connections or voltage control parts.

3 The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution.

box, before any installation, maintenance or repair work is undertaken.

4. Exterior lighting must not be installed during rain.

6. Take account of the minimal separation distance from other objects and the room required around the fitting.

7. If in any doubt, consult a professional, taking local installation requirements into account. Some countries

stipulate that lighting may be installed only by registered installers.

8. Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V

low voltage conductors.

9. When replacing a halogen lamp, wait for it to cool, for a minimum of 5 minutes.

10. Clean with a clean, dry cloth or brush, use no solvent

s or abrasives. Avoid dampness on all electrical

components

11. Take account of all available technical information.

12. Take note of the symbols when connecting wires:

13. Meaning of symbols:

III

220-240V~

50Hz

Max. 50mmø

GU10

2Max.50W

IPXX

3x

min.0,75mm²

8mm

Light Angle

35cm²

55º

SAFETY INSTRUCTION

0.5m

For indoor use only, where direct contact with water is impossible

Protection Class I: the fitting must be earthed

Protection Class II: the fitting is doubled insulated and does not require earthing

Protection Class III: the fitting is low voltage

Minimum distance from lighted objects (meters)

Only the self-shielded halogen lamp should be used with the luminaire

Strip the wire to the indicated length (mm);different items require different length

Connect using the specified cable; different items require different cables

The type of lamp and maximum size and wattage indicated in each lighting unit must not

be exceed; different items require different kind of light sources with different bulb icons

The armature is designed to work only with the indicated voltage. Different items require

different working voltage.

The luminaire can be used in combination with a dimmer

The reference light angle and light space of the luminaire

This luminaire cannot be disposed together with normal domestic waste in standard rubbish

can, but you have to bring it to a staging area for electrical waste

This icon indicates the level of water-proof and dust-proof

N =Neutral L =Live =Earth

this product. Please keep this user manual for further reference

INSTRUCTION MANUALINSTRUCTION MANUAL

220-240V~

50Hz

IP65

1800 LM

18 W

2700 K

>80 Ra

30000 H

Plater CL

step4

Fix the expansion screws on the ceiling Fix the bracket with the screws

Connect the L、N wires

Clip the lamp to the bracket

step1 step2

step3

Plater CL White Round 18W LED

Item number: 96806

Overall size:

220x50mm

Plater CL White Round 18W LED PIR

Item number: 96807

Overall size:

280x50mm

1.To save the power,it would light on when the

environment is less than 100LUX.

Function:

2.When there is movement in the sensor area of

6-10m,it lights on automatically. And it lights off

after 30-40 seconds without movement.

Plater CL White Round 18W LED LUX

Item number: 96808

Overall size:

330x50mm

Function:

1.It would light on when the environment is less

than 100LUX,and light off when the environment

is more than 100LUX.

Plater CL White Square 18W LED Plater CL White Square 18W LED PIR Plater CL White Square 18W LED LUX

Item number: 96809 Item number: 96810 Item number: 96811

Overall size: Overall size: Overall size:220x220x50mm 280x280x50mm 330x330x50mm

Function:

Function:

1.To save the power,it would light on when the

environment is less than 100LUX.

2.When there is movement in the sensor area of

6-10m,it lights on automatically. And it lights off

after 30-40 seconds without movement.

1.It would light on when the environment is less

than 100LUX,and light off when the environment

is more than 100LUX.

Plater CL White Round LED

Plater CL White Square LED

step5

step6

Tighten the screws in the both sides of lamp

Take out the lamp from the bracket

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Qazqa 97681 Plater Lamppu. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Qazqa. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Qazqa 97681 Plater Lamppu käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Qazqa Lamput
Lisää Lamput käsikirjoja

Usein kysytyt kysymykset kohteesta Qazqa 97681 Plater Lamppu

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.