Käyttöohje Philips GC3550 Silitysrauta

Käyttöohje

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the

support that Philips offers, register your product at www.philips.com/welcome.

Important

Read this user manual carefully before you use the appliance and save it for future

reference.

Danger

- Never immerse the iron in water.

Warning

- Check if the voltage indicated on the appliance corresponds to the local mains

voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance itself shows

visible damage, or if the appliance has been dropped or leaks.

- If the mains cord is damaged, you must have it replaced by Philips, a service

centre authorised by Philips or similarly qualied persons in order to avoid a

hazard.

- Never leave the appliance unattended when it is connected to the mains.

- This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- Do not let the mains cord come into contact with the hot soleplate of the iron.

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord regularly for possible damage.

- The soleplate of the iron can become extremely hot and may cause burns if

touched.

- When you have nished ironing, when you clean the appliance, when you ll or

empty the water tank and also when you leave the iron even for a short while:

set the steam control to position 0, put the iron on its heel and remove the

mains plug from the wall socket.

- Always place and use the iron on a stable, level and horizontal surface.

- Do not put perfume, vinegar, starch, descaling agents, ironing aids or other

chemicals in the water tank.

- This appliance is intended for household use only.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards regarding electromagnetic elds

(EMF). If handled properly and according to the instructions in this user manual, the

appliance is safe to use based on scientic evidence available today.

General description (Fig. 1)

A Spray nozzle

B Filling opening with cap

C Steam boost button ( 9)

D Spray button ( 8)

E Steam control

F Amber temperature light (specic types only: with red auto-off indication)

G Calc-Clean button

H Temperature dial

I Mains cord

J Heel

K Anti-Calc tablet (specic types only)

L Water tank

Not shown: lling cup

Before first use

1 Remove any sticker, protective foil or plastic from the soleplate (Fig. 2).

Preparing for use

Filling the water tank

Do not put perfume, vinegar, starch, descaling agents, ironing aids or other

chemicals in the water tank.

1 Make sure the appliance is unplugged.

2 Set the steam control to position 0 (= no steam) (Fig. 3).

3 Openthecapofthellingopening.

4 Tilttheironbackwardsandusethellingcuptollthewatertankwithtap

water up to the maximum level. (Fig. 4)

Do not ll the water tank beyond the MAX indication.

5 Closethecapofthellingopening(‘click’).

Setting the temperature

1 Put the iron on its heel.

2 To set the required ironing temperature, turn the temperature dial to the

appropriate position (Fig. 5).

Check the laundry care label for the required ironing temperature:

- 1 for synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)

- 1 for silk

- 2 for wool

- 3 for cotton and linen

If you do not know what kind or kinds of fabric an article is made of, determine the

right ironing temperature by ironing a part that is not visible when you wear or use

the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent

shiny patches. To prevent stains, do not use the spray function.

Start ironing the articles that require the lowest ironing temperature, such as those

made of synthetic bres.

3 Put the mains plug in an earthed wall socket.

, The amber temperature light goes on (Fig. 6).

4 When the temperature light goes out, wait a while before you start ironing.

The temperature light goes on from time to time during ironing.

Using the appliance

Note: The iron may give off some smoke when you use it for the rst time. This stops after

a short while.

Steam ironing

1 Make sure that there is enough water in the water tank.

2 Settherecommendedironingtemperature(seechapter‘Preparingforuse’,

section‘Settingthetemperature’).

3 Set the appropriate steam setting. Make sure that the steam setting is suitable

for the set ironing temperature: (Fig. 7)

- 1 - 2 for moderate steam (temperature settings 2 to 3)

- 3 - 4 for maximum steam (temperature settings 3 to MAX)

Note: The iron starts to produce steam as soon as it has reached the set temperature.

Note: If the selected ironing temperature is too low (MIN to 2), water may drip from

the soleplate (see chapter ‘Features’, section ‘Drip stop’).

Ironing without steam

1 Set the steam control to position 0 (= no steam) (Fig. 3).

2 Settherecommendedironingtemperature(seechapter‘Preparingforuse’,

section‘Settingthetemperature’).

Features

Spray function

You can use the spray function at any temperature to moisten the article to be

ironed. This helps remove stubborn creases.

1 Make sure that there is enough water in the water tank.

2 Press the spray button several times to moisten the article to be

ironed (Fig. 8).

Steam boost

A powerful steam boost helps to remove very stubborn creases.

The steam boost function can only be used at temperature settings between 2 and

MAX.

1 Press and release the steam boost button (Fig. 9).

Concentrated steam boost from the special Steam Tip (specic

types only)

The concentrated steam boost from the long vents in the Steam Tip enhances the

distribution of steam into every part of your garment. The concentrated steam boost

function can only be used at temperature settings between 2 and MAX.

1 Press and release the steam boost button (Fig. 10).

Vertical steam boost

You can also use the steam boost function when you hold the iron in vertical position.

This is useful for removing creases from hanging clothes, curtains etc.

1 Hold the iron in vertical position and press and release the steam boost

button (Fig. 11).

Never direct the steam at people.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Philips GC3550 Silitysrauta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Philips. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Philips GC3550 Silitysrauta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Philips Silitysraudat
Lisää Silitysraudat käsikirjoja

Usein kysytyt kysymykset kohteesta Philips GC3550 Silitysrauta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Philips GC9646 PerfectCare Silitysrauta

Käyttöohje

Philips GC9545 Silitysrauta

Käyttöohje

Philips GC9236 Silitysrauta

Käyttöohje

Philips GC7051 Silitysrauta

Käyttöohje

Philips GC9224 Silitysrauta

Käyttöohje

Philips GC6815 Silitysrauta

Käyttöohje

Philips HI5914 Silitysrauta

Käyttöohje

Philips DST7011 Silitysrauta

Aiheeseen liittyvät luokat