Käyttöohje Nedis HCBL400WT Verenpainemittari

Käyttöohje

a

Quick start guide

Blood Pressure Monitor

HCBL400WT

For more information see the extended manual online: ned.is/hcbl400wt

Intended use

This product is intended to measure the diastolic and systolic blood pressure and pulse rate

of an adult.

The product is not intended for use on neonates, children or pregnant women.

This product is not intended for medical use.

The product is intended for indoor use only.

Any modication of the product may have consequences for safety, warranty and proper

functioning.

Specications

Product Blood Pressure Monitor

Article number HCBL400WT

Dimensions (l x w x h) 136 x 120 x 61 mm

Weight (excl. batteries and cu) 225g

Cu circumference 22 - 42 cm

Measuring method Oscillometric method, automatic ination and measurement

Measurement range

Cu pressure 0 - 300 mmHg

Systolic 60 - 260 mmHg

Diastolic 40 - 199 mmHg

Pulse rate 40 - 180 beats/minute

Accuracy

Pressure ± 3 mmHg

Pulse rate Less than 60: ±3bpm

More than 60 (incl.) : ±5%

Precision 1 mmHg

Memory 2 x 60 measurements

Battery type 4 x 1.5 V AA batteries (not included)

Battery life Approximately 270 times

Operating temperature 10 - 40 °C

Storage temperature -20 - 50 °C

Relative humidity ≤85 %

Environmental pressure 80 - 105 kPa

Main parts (image A)

1 Storage bag

2 Cu

3 Rubber air tube

4 Air tube connector

5 Battery compartment

6 Memory button

7 Start button

8 Irregular heartbeat indicator

9 Low battery indicator

q Pressure in the cu is instable or there is a lot of

remnant air in the cu

w Blood pressure level classication indicator

e Time and date display

r Systolic blood pressure

t Diastolic blood pressure

y Pulse rate

Safety instructions

-

WARNING

• Ensure you have fully read and understood the instructions in this document before you

install or use the product. Keep the packaging and this document for future reference.

• Only use the product as described in this document.

• Do not use the product if a part is damaged or defective. Replace a damaged or defective

product immediately.

• Do not drop the product and avoid bumping.

• Do not expose the product to water or moisture.

• Only use the provided power cable.

• Disconnect the product from the power source and other equipment if problems occur.

• Do not unplug the product by pulling on the cable. Always grasp the plug and pull.

• This product may only be serviced by a qualied technician for maintenance to reduce the

risk of electric shock.

• Consult with a doctor before use if you have any medical concerns.

• Do not use this product in a moving vehicle. This may result in inaccurate measurements.

Inserting the batteries (image B)

1. Open the battery compartment A

5

.

2. Place the batteries.

3. Close A

5

.

Setting the time and date

1. Press and hold the start button A

7

and the memory button A

6

simultaneously for two

seconds.

The time format starts to blink. The product is now in time format adjustment mode.

4

If no button is pressed for 60 seconds, the product exits time and date adjustment mode.

2. Press A

6

to change the time format.

3. Press A

7

to conrm.

The product is now in year adjustment mode.

4. Press A

6

to adjust the number.

5. Press A

7

to conrm.

The product is now in month adjustment mode.

6. Repeat steps 4 – 5 to set the month, date, hour and minutes.

Connecting the cu

1. Insert the rubber air tube A

3

into the air tube connector A

4

.

4

The connector must be completely inserted to prevent air leakage during blood pressure

measurements.

Applying the cu

1. Place the cu A

2

around a bare upper arm.

4

A

2

must be placed 1-2 cm above the elbow joint.

2. Choose an arm to measure on. Always measure on the same arm.

4

If A

2

is applied on the left arm, A

3

must be on the inside of the arm, aligned with the

middle nger.

4

If A

2

is applied on the right arm, A

3

must be at the side of the elbow.

4

A

2

should be tight but comfortable. It should be possible to insert a nger between the

arm and A

2

.

Body posture during measurement

Sitting down

1. Sit down.

2. Put your feet at on the oor.

3. Place your hand on a at surface with the palm up.

4

Do not rest your arm on A

3

. This may restrict the airow to A

2

.

4. Position your arm so A

2

is at the same height as your heart.

5. Sit calmly for 5 minutes before starting the blood pressure measurement.

Lying down

1. Lie on your back.

2. Place your arm straight along your side with the palm up.

3. Position your arm so A

2

is at the same height as your heart.

4. Lie calmly for 5 minutes before starting the blood pressure measurement.

Measuring blood pressure

1. Press A

7

.

4

All symbols - A

8

to A

y

- are shown on the display. If not all symbols are visible, contact

the service center.

The current memory group starts to blink in the place of A

t

.

4

Memory groups can be used to store measurements for multiple people on the same

device.

2. Press A

6

to switch memory groups.

3. Press A

7

to conrm.

4

The memory group is also conrmed automatically after 5 seconds of inactivity.

The display shows the most recent measurements.

If no measurements are stored in the memory group, the display shows zeroes.

The product starts to seek zero pressure.

A

2

inates until sucient pressure has built up for a measurement.

A

2

slowly deates while the measurement is carried out.

The results are shown on the display.

4

The measurements are automatically stored.

4. Press A

7

to switch o the display manually.

4

The display switches o automatically after 1 minute of inactivity.

Reading measurements from the memory

1. Press A

6

.

The current memory group is shown in the place of A

t

.

2. Press A

7

to switch memory groups.

3. Press A

6

to conrm.

4

The memory group is also conrmed automatically after 5 seconds of inactivity.

The display shows the average values of all measurements in the current memory group.

If no measurements are stored in the memory group, the display shows zeroes.

4. Press A

6

to show the average values of the last three measurements in the current

memory group.

5. Press A

6

to show the number of stored measurements in the current memory group.

6. Press A

6

to show the most recent measurements.

7. Press A

6

repeatedly to show the previous measurements.

8. Press A

7

to switch o the display manually.

4

The display switches o automatically after 1 minute of inactivity.

Deleting measurements from the memory

1. When the display shows a measurement, press and hold A

6

for three seconds to delete

all measurements in the current memory bank.

Technical alarm

If the measured blood pressure is outside the rated range, the display shows ‘Hi’ or ‘Lo’ as

technical alarm.

1. Check if the measurement was performed correctly.

2. If the measurement was performed correctly, consult your physician.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Nedis HCBL400WT Verenpainemittari. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Nedis. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Nedis HCBL400WT Verenpainemittari käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Nedis Verenpainemittarit
Lisää Verenpainemittarit käsikirjoja

Usein kysytyt kysymykset kohteesta Nedis HCBL400WT Verenpainemittari

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Nedis BLPR110WT Verenpainemittari

Käyttöohje

Medisana HGV Verenpainemittari

Käyttöohje

Medisana MTD Verenpainemittari

Käyttöohje

Topcom BPM ARM 5000 Verenpainemittari

Käyttöohje

Medisana MTM Verenpainemittari

Käyttöohje

Medisana BPW 300 Verenpainemittari

Käyttöohje

Medisana HGH Verenpainemittari

Käyttöohje

Medisana BW 310 Verenpainemittari

Aiheeseen liittyvät luokat