Käyttöohje Makita 9901 Nauhahiomakone

Käyttöohje

4

ENGLISH

Explanation of general view

1Lever

2 Adjusting knob

3 Dust spout

4 Dust bag

5 Switch trigger

6 Lock button

7 Speed change switch

8 Limit mark

9 Brush holder cap

10 Screwdriver

SPECIFICATIONS

Model Belt size Belt speed Overall length Net weight

9401 .........................................100 mm x 610 mm 350 m/min 374 mm 7.3 kg

9402 .........................................100 mm x 610 mm H 350 m/min 374 mm 7.3 kg

L 300 m/min

9900B .........................................76 mm x 533 mm 360 m/min 316 mm 4.6 kg

9901 ........................................... 76 mm x 533 mm 380 m/min 328 mm 3.5 kg

9924DB ......................................76 mm x 610 mm 400 m/min 355 mm 4.8 kg

360 m/min (U.K. only)

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

ADDITIONAL SAFETY RULES

ENB007-2

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

2. Hold the tool firmly with both hands.

3. Make sure the belt is not contacting the work-

piece before the switch is turned on.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. This tool has not been waterproofed, so do not

use water on the workpiece surface.

7. Ventilate your work area adequately when you

perform sanding operations.

8. Some material contains chemicals which may be

toxic. Take caution to prevent working dust inha-

lation and skin contact. Follow material supplier

safety data.

9. Always use the correct dust mask/respirator for

the material and application you are working

with.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing abrasive belt (Fig. 1 & 2)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the belt.

Pull the lever all the way out and install the belt over the

rollers, then return the lever to the original position.

CAUTION:

When installing the belt, make sure that the direction of

the arrow on the back of the belt corresponds to the one

on the tool itself.

Adjusting belt tracking (Fig. 3)

While the belt is running, use the adjusting knob to center

the belt tracking. Failure to do so can result in frayed belt

edges and wear on the sander frame.

Dust bag (Fig. 4)

The use of the dust bag makes sanding operations clean

and dust collection easy. To attach the dust bag, fit it onto

the dust spout.

For the best results, empty the dust bag when it becomes

about half full, tapping it lightly to remove as much dust

as possible.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Speed change (Fig. 6)

For Model 9402

To change the tool speed, press the “H” side of the speed

change switch for high speed or the “L” side for low

speed.

CAUTION:

Use the speed change switch only after the tool comes to

a complete stop.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Makita 9901 Nauhahiomakone. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Makita. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Makita 9901 Nauhahiomakone käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Makita Nauhahiomakoneet
Lisää Nauhahiomakoneet käsikirjoja

Usein kysytyt kysymykset kohteesta Makita 9901 Nauhahiomakone

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Makita 9402 Nauhahiomakone

Käyttöohje

Makita 9911 Nauhahiomakone

Käyttöohje

Makita 9900B Nauhahiomakone

Käyttöohje

Makita 9924DB Nauhahiomakone

Käyttöohje

Makita 9921 Nauhahiomakone

Käyttöohje

Makita 9910 Nauhahiomakone

Käyttöohje

Makita 9401 Nauhahiomakone

Käyttöohje

Bosch GBS 75 AE Nauhahiomakone

Aiheeseen liittyvät luokat