Käyttöohje Makita 9520NB Kulmahiomakone

Käyttöohje

ENGLISH

Explanation of general view

1 Wheel guard

2 Bearing box

3 Screw

4 Lock nut

5 Depressed center wheel

6 Inner flange

7 Spindle

8 Lock nut wrench

9 Shaft lock

10 Switch lever

11 Limit mark

12 Brush holder cap

13 Screwdriver

SPECIFICATIONS

Model 9520NB 9521NB 9522NB

Depressed center wheel diameter ................................... 100 mm 115 mm 125 mm

Spindle thread .................................................................. M10 M14 M14

No load speed (min

-1

) ...................................................... 12,000 12,000 9,500

Overall length ................................................................... 262 mm 262 mm 262 mm

Net weight ........................................................................ 1.3 kg 1.3 kg 1.3 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES ENB031-3

1. Always wear safety goggles and ear protec-

tors during operation.

2. Always be sure that the tool is switched off

and unplugged before carrying out any work

on the tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels

having a maximum operating speed at least as

high as the highest No Load Speed marked on

the tool’s nameplate.When using depressed

center wheels, be sure to use only fiberglass-

reinforced wheels.

5. Check the wheel carefully for cracks or dam-

age before operation. Replace cracked or

damaged wheel immediately.

6. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

7. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (espe-

cially the installing surface) or the lock nut.

Damage to these parts could result in wheel

breakage.

10. For tools intended to be fitted with threaded

hole wheel, ensure that the thread in the wheel

is long enough to accept the spindle length.

11. Before using the tool on an actual workpiece,

test run the tool at the highest no load speed

for at least 30 seconds in a safe position. Stop

immediately if there is any vibration or wob-

bling that could indicate poor installation or a

poorly balanced wheel. Check the tool to

determine the cause.

12. Check that the workpiece is properly sup-

ported.

13. Hold the tool firmly.

14. Keep hands away from rotating parts.

15. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

16. Use the specified surface of the wheel to

perform the grinding.

17. Do not use cutting off wheel for side grinding.

18. Watch out for flying sparks. Hold the tool so

that sparks fly away from you and other per-

sons or flammable materials.

19. Pay attention that the wheel continues to

rotate after the tool is switched off.

20. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

21. Position the tool so that the power cord

always stays behind the tool during operation.

22. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a

short-circuit breaker (30 mA) to assure opera-

tor safety.

23. Do not use the tool on any materials contain-

ing asbestos.

24. Do not use water or grinding lubricant.

SAVE THESE INSTRUCTIONS.

9520NB (’100. 12. 21)

5

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Makita 9520NB Kulmahiomakone. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Makita. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Makita 9520NB Kulmahiomakone käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Makita Kulmahiomakoneet
Lisää Kulmahiomakoneet käsikirjoja

Usein kysytyt kysymykset kohteesta Makita 9520NB Kulmahiomakone

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Makita 9047S Kulmahiomakone

Käyttöohje

Makita 9521NB Kulmahiomakone

Käyttöohje

Makita 9565Z Kulmahiomakone

Käyttöohje

Makita 9067SF Kulmahiomakone

Käyttöohje

Makita 9562C Kulmahiomakone

Käyttöohje

Makita 9566C Kulmahiomakone

Käyttöohje

Makita 9067L Kulmahiomakone

Käyttöohje

Makita 9047 Kulmahiomakone

Aiheeseen liittyvät luokat