Käyttöohje Makita 6798FD Ruuvitaltta

Käyttöohje

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a fire.

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well

ventilated area during charging.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB026-1

1. Be aware that this tool is always in an operat-

ing condition, because it does not have to be

plugged into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a

‘‘live’’wire will also make exposed metal parts

of the tool ‘‘live’’ and shock the operator.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

•

Always switch off the tool before insertion or

removal of the battery cartridge.

•

To remove the battery cartridge, pull out the set

plate on the tool and grasp both sides of the

cartridge while withdrawing it from the tool.

•

To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the tool.

•

Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging

Before using battery charger, read all instructions and

cautionary markings on the battery charger.

Tips for maintaining maximum battery life

1. Always stop tool operation and charge the battery

cartridge when you notice that the warning lamp

lightened up.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before

charging it.

Installing or removing bit (Fig. 2)

CAUTION:

Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing the bit.

Use only the driver bit or socket bit shown in the figure

below.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of

the arrow and pull the bit out firmly.

Adjusting the fastening torque (Fig. 3)

Use an optional adjust grip to adjust the fastening

torque.

Insert the pins of the adjust grip into the holes in the

front of the tool. And then, turn the adjust grip so that

the torque gauge shows the desired torque by one of

the numbers from 1 to 12.

The number provides fastening torque in newton-

meter (N

.

m), and see below for the standard fastening

torque;

6796D/FD: 1 – 5 (Nzm)

6797D/FD: 2 – 8 (Nzm)

6798D/FD: 6 – 12 (Nzm)

After completion of the adjustment, always make trial

fastening about twenty times in order to keep stability

of torque. Then, check the fastening torque with a

torque tester before starting operation.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the ‘‘OFF’’ position when

released.

To start the tool, simply pull the trigger. Release the

trigger to stop.

Lighting up front lamps (Fig. 5)

(for 6796FD/6797FD/6798FD only)

Pull the trigger to light up the front lamps. And the

lamps keep on lighting while the trigger is being

pulled. The light automatically goes out 10 to 20

seconds after the trigger is released.

5

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Makita 6798FD Ruuvitaltta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Makita. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Makita 6798FD Ruuvitaltta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Makita Ruuvitaltat
Lisää Ruuvitaltat käsikirjoja

Usein kysytyt kysymykset kohteesta Makita 6798FD Ruuvitaltta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Makita 6797FD Ruuvitaltta

Käyttöohje

Makita 6833 Ruuvitaltta

Käyttöohje

Makita 6705DW Ruuvitaltta

Käyttöohje

Makita BFR440 Ruuvitaltta

Käyttöohje

Makita 6821 Ruuvitaltta

Käyttöohje

Makita 6795D Ruuvitaltta

Käyttöohje

Makita 6820V Ruuvitaltta

Käyttöohje

Makita 6796FD Ruuvitaltta

Aiheeseen liittyvät luokat