Käyttöohje Makita 4324 Kuviosaha

Käyttöohje

ENGLISH

Explanation of general view

1 Bolt

2 Hex wrench

3 Loosen

4 Blade holder

5 Jig saw blade

6 Roller

7 Hook

8 Dust cover

9 Switch trigger

0 Lock button

q Cutting action changing lever

w Speed adjusting dial

e Cutting line

r Base

t Bolt

y Graduations

u Edge of motor housing

i Starting hole

o Hose

p Rip fence

a Bolt

s Fence guide

d Threaded knob

f Circular guide pin

g Protrusions

h Anti-splintering device

SPECIFICATIONS

Model 4324

Length of stroke ............................................. 18 mm

Strokes per minute ................................ 500 – 3,100

Cutting capacities

Wood ........................................................... 65 mm

Mild steel ....................................................... 6 mm

Overall length ............................................... 207 mm

Net weight ....................................................... 1.9 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

2. Do not cut hollow pipe.

3. Do not cut oversize workpiece.

4. Check for the proper clearance beneath the

workpiece before cutting so that the blade will

not strike the floor, workbench, etc.

5. Hold the machine firmly.

6. Make sure the blade is not contacting the

workpiece before the switch is turned on.

7. Keep hands away from moving parts.

8. When cutting through walls, floors or wher-

ever ‘‘live’’ electrical wires may be encoun-

tered, DO NOT TOUCH ANY METAL PARTS OF

THE MACHINE! Hold the machine only by the

insulated grasping surfaces to prevent electric

shock if you cut through a ‘‘live’’ wire.

9. Do not leave the machine running. Operate the

machine only when hand-held.

10. Always switch off and wait for the blade to

come to a complete stop before removing the

blade from the workpiece.

11. Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing saw blade (Fig.1&2)

CAUTION:

•

Always be sure that the machine is switched off and

unplugged before installing or removing the blade.

•

Always clean out all chips or foreign matter adher-

ing to the blade and/or blade holder. Failure to do so

may cause insufficient tightening of the blade,

resulting in a serious injury.

To install the blade, loosen the bolt on the blade

holder with the hex wrench. With the blade teeth

facing forward, insert the blade into the blade holder

as far as it will go. Make sure that the back edge of the

blade fits into the roller. Then tighten the bolt to secure

the blade.

To remove the blade, follow the installation proce-

dures in reverse.

NOTE:

Occasionally lubricate the roller.

Hex wrench storage (Fig. 3)

When not in use, the hex wrench can be conveniently

stored as shown in Fig. 3.

Dust cover (Fig. 4)

CAUTION:

Always wear safety goggles even when operating the

machine with the dust cover lowered.

Lower the dust cover to prevent chips from flying.

However, when making bevel cuts, raise it all the way.

Switch action (Fig. 5)

CAUTION:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

To start the machine, simply pull the trigger. Release

the trigger to stop. For continuous operation, pull the

trigger and then push in the lock button. To stop the

machine from the locked position, pull the trigger fully,

then release it.

6

4324 (E) (’98. 7. 24)

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Makita 4324 Kuviosaha. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Makita. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Makita 4324 Kuviosaha käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Makita Kuviosahat
Lisää Kuviosahat käsikirjoja

Usein kysytyt kysymykset kohteesta Makita 4324 Kuviosaha

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Makita 4323 Kuviosaha

Käyttöohje

Makita 4334D Kuviosaha

Käyttöohje

Makita BJV180ZX Kuviosaha

Käyttöohje

Makita 4341CT Kuviosaha

Käyttöohje

Makita 4340T Kuviosaha

Käyttöohje

Makita 4341T Kuviosaha

Käyttöohje

Makita 4331D Kuviosaha

Käyttöohje

Makita BJV180RFX Kuviosaha

Aiheeseen liittyvät luokat