Käyttöohje Hoover HP320PET 011 Pölynimuri

Käyttöohje

3

A. Do the lters need cleaning? If so refer to ‘Cleaning the washable lters’.

B. Check if there is any other blockage in the system - Use a rod or pole to remove

any blockage from the extension tube or exible hose.

C. Check if pre-motor lter is tted.

D. Check if the separation unit needs to be cleaned. Refer to ‘Cleaning the

separation unit

’

.

Warning - If the cleaner is used for a signicant period of time with a blockage, a thermal

cut out will switch the cleaner off to prevent overheating. If this should happen, switch

the cleaner off, unplug and correct the fault. It will take about 45 minutes for the cutout to

automatically reset.

USER CHECKLIST

Should you have a problem with the product, complete this simple user checklist before

calling your local Hoover service.

• Is there a working electricity supply to the cleaner? Please check with another

electrical appliance.

• Is the dust container over-lled? Please refer to ‘Cleaner Maintenance’.

• Is the lter blocked? Please refer to ‘Cleaner Maintenance’.

• Is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the system’.

• Has the cleaner overheated? If so, it will take approximately 45 minutes to automatically

reset.

IMPORTANT INFORMATION

Hoover spares and Consumables

Always replace parts with genuine Hoover spares. These are available from your local

Hoover dealer or direct from Hoover. When ordering parts always quote your model

number.

Hoover Service

Should you require service at any time, please contact your local Hoover Service Ofce.

Quality

Hoover’s factories have been independently assessed for quality. Our products are made

using a quality system which meets the requirements of ISO 9001.

Your Guarantee

The guarantee conditions for this appliance are as dened by our representative in the

country in which it is sold. Details regarding these conditions can be obtained from the

dealer from whom the appliance was purchased. The bill of sale or receipt must be

produced when making any claim under the terms of this guarantee.

Subject to change without notice.

* Certain Models Only ** May vary according to model

clean your lters may result in air blockage, overheating and product failure.

This may invalidate your guarantee.

IMPORTANT: Regularly check and maintain the lters.

IMPORTANT: Always ensure the lters are fully dry before use.

To access the pre-motor lter:

1. Pull the dust bin release button and remove the dust bin from the cleaner. [12]

2. Hold the dust bin with one hand and with the other hand remove the dust bin lid by

rotating anti-clockwise. [14]

3. Remove the pre-motor lter assembly from the bin and separate the lter from the

lter frame. [15,16]

4. Gently tap and wash the pre-motor lter and the frame. Do not use hot water or

detergents. Remove excess water from the lter and leave to dry fully before re-

using. [20,21]

5. Reassemble the pre-motor lter assembly once fully dry and ret to the cleaner.

IMPORTANT: The bin lid will NOT close if the pre-motor lter is not assembled to the

Dust Bin. Always ensure the pre-motor lter is present when closing the bin lid.

To access the exhaust lter:

1. Unclip the exhaust lter cover from the rear of the cleaner main body. [18]

2. Remove the exhaust lter from the rear of the cleaner. [19]

3. Gently tap and wash the lter using warm water. Do not use hot water or detergents.

Remove excess water from the lter and leave to dry fully before re-using. [20,21]

4. Ret the exhaust lter to the rear of the cleaner once fully dry and ret the exhaust

lter cover.

IMPORTANT: Do not use the product without the lter pack tted.

Cleaning the dust container / separation unit

This cleaner uses a separation system unique to Hoover. If necessary, the separation

unit can be disassembled from the dust container and cleaned.

1. Pull the dust bin release button and remove the bin assembly from the cleaner. [14]

2. Hold the bin with one hand and with the other hand remove the dust bin lid by rotating

anti-clockwise. [14]

3. Remove the pre-motor lter assembly from the dust bin. And then remove the vortex

nder. [15,17]

4. If necessary, use a cloth to remove excessive dust from the vortex nder surface.

5. Place the dust bin under the tap. Rinse with lukewarm water. Wash internal surfaces of

the dust bin with water only. DO NOT use soap detergents to wash the internals of the

dust bin.

6. Reassemble the internal components to the dust bin, ensuring all components are dry.

7. Close over the dust bin lid and ret dust bin assembly to cleaner.

Removing a blockage

1. Check if the Dust Bin is full. If so, refer to ‘Emptying the Dust Bin’.

2. If the Dust Bin is empty, but suction is still low:

GB

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Hoover HP320PET 011 Pölynimuri. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Hoover. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Hoover HP320PET 011 Pölynimuri käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Hoover Pölynimurit
Lisää Pölynimurit käsikirjoja

Usein kysytyt kysymykset kohteesta Hoover HP320PET 011 Pölynimuri

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Hoover TXL21PET011 Pölynimuri

Käyttöohje

Hoover HF222RXL 011 Pölynimuri

Käyttöohje

Hoover TCP1805 011 Capture Pölynimuri

Käyttöohje

Hoover HF522STH 011 Pölynimuri

Käyttöohje

Hoover TS1961 011 Sensory Pölynimuri

Käyttöohje

Hoover TE75PET 011 Pölynimuri

Käyttöohje

Hoover HF222BPE 011 Pölynimuri

Käyttöohje

Hoover HG530H 011 Pölynimuri

Aiheeseen liittyvät luokat