Käyttöohje Hikoki H 60ME Murtovasara

Käyttöohje

4

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed in the below.

○ Plastic case ................................................................. 1

○ Bull Point (SDS-max shank) ........................................ 1

○ Side Handle ................................................................ 1

Standard accessories are subject to change without notice.

APPLICATIONS

Demolishing concrete, chipping off concrete, grooving, bar

cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility installation,

machinery installation, water supply and drainage work,

interior jobs, harbor facilities and other civil engineering

works.

SPECIFICATIONS

The specifi cations of this machine are listed in the Table on

page 105.

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Inserting SDS-max tools 1 106

Removing SDS-max tools 2 106

Changing tool direction 3 106

Selecting the operating mode 4 106

Adujsting the side handle position 5 106

Switch operation 6 107

Locking-on the On / Off switch 7 107

Releasing the On / Off switch 8 107

About the power lamp 9 107

Speed change 10 108

How to use the demolition hammer*

1

11 108

Selecting accessories*

2

–

109

*1 Operate this Demolition Hammer by utilizing its empty

weight. The performance will not be better even if it is

pressed or thrust forcibly against the work surface.

Hold this Demolition Hammer with a force just suffi cient

to counteract the reaction.

CAUTION

After long time of use, the housing becomes hot.

Therefore, be careful not to burn your hands.

*2 For detailed information regarding each tool, contact a

HiKOKI authorized service center.

Warming up (Fig. 11)

The grease lubrication system in this unit may require

warming up in cold regions.

Position the end of the bit so makes contact with the

concrete, turn on the switch and perform the warming

up operation. Make sure that a hitting sound is produced

and then use the unit.

ABOUT THE PROTECTION

FUNCTION

This tool has a built-in protection circuit for preventing

damage to the unit in the event of an abnormality. Depending

on the nature of the abnormality, the display lamp will fl ash

as shown in Table 1 and the unit will cease to operate. In

such cases, verify the problem indicated by the fl ashing and

take whatever steps are necessary to correct the problem.

NOTE

Repair may be required if the display lamp continues to

fl ash after taking all necessary steps to correct the problem.

If the problem persists, please arrange for repairs.

Table 1

Display

lamp

fl ashing

Cause Solution

Flash

Internal temperature

has risen beyond

the unit’s specifi ed

temperature.

(Temperature

increase protection

function)

Turn off the unit

and allow it to cool

down for about 15 to

30 minutes.

When the temperature

goes down, press the

impact rate selector

switch to recover.

Flash

Excessive pressure

applied to the tool

has resulted in an

overload.

(Overload

protection function)

Press the impact rate

selector switch to

recover. Try to avoid

tasks that will apply

excess pressure to

the unit.

Flash

Tool is connected

to a power source

whose voltage is

either too high or

too low.

(Circuit protection

function)

Connect the unit to a

power supply matching

the input voltage

specifi ed on the

nameplate. Press the

impact rate selector

switch to recover.

Flash

Sensor signal read

error.

(Control monitoring

function)

Press the impact rate

selector switch to

recover. Repair may

be required if this error

continuously occurs.

GREASE REPLACEMENT

This Demolition Hammer is of full air-tight construction to

protect against dust and to prevent lubricant leakage.

Therefore, this Demolition Hammer can be used without

lubrication for long periods. Replace the grease as described

below.

Grease Replacement Period

After purchase, replace grease after every 6 months of

usage. Ask for grease replacement at the nearest authorized

Service Center.

000Book̲H60ME.indb4000Book̲H60ME.indb4 2017/12/0416:22:032017/12/0416:22:03

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Hikoki H 60ME Murtovasara. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Hikoki. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Hikoki H 60ME Murtovasara käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Hikoki Murtovasarat
Lisää Murtovasarat käsikirjoja

Usein kysytyt kysymykset kohteesta Hikoki H 60ME Murtovasara

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Hikoki H 41ME Murtovasara

Käyttöohje

Hikoki H 45ME Murtovasara

Käyttöohje

Hikoki H 65SB3 Murtovasara

Käyttöohje

Hikoki H 25PV Murtovasara

Käyttöohje

Makita HM1213C Murtovasara

Käyttöohje

Makita HM1317CB Murtovasara

Käyttöohje

Makita HM1242C Murtovasara

Käyttöohje

Makita HM1200 Murtovasara

Aiheeseen liittyvät luokat