Käyttöohje Hikoki DS 18DD Porakone-ruuvinväännin

Käyttöohje

7

English

15 Resting the unit after continuous work.

16. After use for continuous tightening wood screw works,

rest the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc., will

rise if the work is started again immediately after battery

replacement, eventually resulting in burnout.

17. The motor may stop in the event the tool is overloaded. In

this should occur, release the tool’s switch and eliminate

the cause of the overload.

18. The motor rotation may be locked to cease while the unit

is used as drill. While operating the driver drill, take care

not to lock the motor.

19. If motor is locked, immediately turn the power off . If the

motor is locked for a while, the motor or battery may be

burnt.

20. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

21. Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

22. To prevent the battery power consumption caused

by forgetting to turn off the LED light, the light goes off

automatically in about 10 seconds.

23. Do not look directly into the light. Such actions could

result in eye injury.

24. Always use the tool and the battery at temperatures

between -5°C and 40°C.

25. Always charge the battery at an ambient temperature of

0 – 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

specifi ed.

7. If the battery charging fails to complete even when a

specifi ed recharging time has elapsed, immediately stop

further recharging.

8. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

9. Keep away from fi re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

12. Do not immerse the battery or allow any fl uids to fl ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in fi re or explosion. Store your

battery in a cool, dry place, away from combustible and

fl ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you fi nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the fi rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium

ion battery, the battery may be shorted, causing fi re. When

storing the lithium ion battery, obey surely the rules of

following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe the

following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100 Wh are considered to be in the freight classifi cation

of Dangerous Goods and will require special application

procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

00BookDS18DD.indb700BookDS18DD.indb7 2020/04/2310:06:272020/04/2310:06:27

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Hikoki DS 18DD Porakone-ruuvinväännin. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Hikoki. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Hikoki DS 18DD Porakone-ruuvinväännin käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Hikoki Porakone-ruuvinvääntimet
Lisää Porakone-ruuvinvääntimet käsikirjoja

Usein kysytyt kysymykset kohteesta Hikoki DS 18DD Porakone-ruuvinväännin

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Hikoki DV 18DGAL Porakone-ruuvinväännin

Käyttöohje

Hikoki DS 9DVF3 Porakone-ruuvinväännin

Käyttöohje

Hikoki DS 14DCL Porakone-ruuvinväännin

Käyttöohje

Hikoki DS 10DAL Porakone-ruuvinväännin

Käyttöohje

Hikoki DV 18DD Porakone-ruuvinväännin

Käyttöohje

Hikoki DS 14DL2 Porakone-ruuvinväännin

Käyttöohje

Hikoki DS 14DSDL Porakone-ruuvinväännin

Käyttöohje

Skil 3065 HB Porakone-ruuvinväännin

Aiheeseen liittyvät luokat