Käyttöohje Greenworks G24AG Kulmahiomakone

Käyttöohje

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

English (Original Instructions)

3

■ Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

■ Do not discard the packing material until you have

carefully inspected and satisfactorily operated the tool.

WARNING

If any parts are damaged or missing do not operate

this product until the parts are replaced. Use of this

product with damaged or missing parts could result in

serious personal injury.

WARNING

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modication is misuse

and could result in a hazardous condition leading to

possible serious personal injury.

WARNING

To prevent accidental starting that could cause

serious personal injury, always remove the battery

pack from the product when assembling parts.

Battery Charging

■ Use only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery

of your power tool.

Note: The battery supplied is partially charged. To ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time.

The lithium-ion battery can be charged at any time

without reducing its service life. Interrupting the charging

procedure does not damage the battery.

The lithium-ion battery is protected against deep

discharging by the “Electronic Cell Protection (ECP)”.

When the battery is empty, the machine is switched off by

means of a protective circuit: The inserted tool no longer

rotates.

■ Do not continue to press the On/Off switch after the

machine has been automatically switched off. The

battery can be damaged.

Observe the notes for disposal.

Removing the battery (see gure A)

To remove the battery, press the battery unlocking button

13 and pull the battery 12 out of the power tool toward the

rear. Do not exert any force.

Installing Grinding Wheel (see gure B)

DANGER

Never attach a wood cutting or carving blade of any

type to this grinder. It is only designed for grinding

and sanding. Use for any other purpose is not

recommended and creates a hazard, which will result

in serious injury.

WARNING

Thoroughly inspect a new grinding wheel before you

install it on the grinder.

■ Tap lightly around the wheel using a wooden

hammer.

■ Listen carefully to the resulting sounds. Places with

fissures or cracks will result in a different sound.

Do not use a wheel containing ssures or cracks.

When you install a new grinding wheel, carry out a no

load revolution test of approximately one minute with

the grinding wheel facing a safe direction, i.e., away

from people or objects.

■ Depress the spindle lock button and rotate the clamp

nut until the spindle locks.

NOTE: To prevent damage to the spindle or spindle

lock, always allow motor to come to a complete stop

before engaging spindle lock.

■ Loosen (fig.B.3) and remove the clamp nut from the

spindle. Do not remove the disc flange.

■ Make sure the flats on the bottom of the disc flange are

engaged with the flats on the spindle.

■ Place the grinding wheel over the spindle.

WARNING

Always install a grinding wheel with the depressed

center against the disc ange. Failure to do so will

cause the grinding wheel to crack when tightening the

clamp nut. This could result in serious personal injury

because of loose particles breaking off and being

thrown from the grinder. Do not overtighten.

■ Thread the clamp nut on the spindle with the flat side

of the nut facing up.

■ Fit the raised, small diameter portion of the clamp nut

into the hole in the wheel and finger tighten.

■ Depress the spindle lock button and rotate the wheel

clockwise (fig.B.2) until the spindle locks in position.

■ Tighten the clamp nut securely with the wrench 14

provided. Do not overtighten.

Installing The Side Handle (see gure C)

WARNING

The side handle must always be used to help prevent

loss of control and possible serious injury.

The side handle can be installed on the left or right side of

the grinder, depending on operator preference.

■ Insert the side handle into the desired operating

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Greenworks G24AG Kulmahiomakone. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Greenworks. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Greenworks G24AG Kulmahiomakone käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Greenworks Kulmahiomakoneet
Lisää Kulmahiomakoneet käsikirjoja

Usein kysytyt kysymykset kohteesta Greenworks G24AG Kulmahiomakone

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Greenworks GD24AG Kulmahiomakone

Käyttöohje

Parkside PWS 125 F5 Kulmahiomakone

Käyttöohje

Ryobi RAG18125-0 Kulmahiomakone

Käyttöohje

Bosch PWS 8500-125 Kulmahiomakone

Käyttöohje

Metabo WPB 18 LTX BL 125 Quick Kulmahiomakone

Käyttöohje

Bosch GWX 18V-10 Kulmahiomakone

Käyttöohje

Parkside IAN 56295 Kulmahiomakone

Käyttöohje

Meec Tools 018-600 Kulmahiomakone

Aiheeseen liittyvät luokat