Käyttöohje FERM TDM1011 Pöytäporakone

Käyttöohje

50 Ferm

SPARE PARTS LIST

POSITION DESCRIPTION NO.

28 SPRING-TERSION 311106

29 CAP-SPRING 311107

38 MOTOR 311103

59 V-BELT 311104

2 RACK 311108

64 SWITCH 311105

79 KEY-DRIFT 311109

10 ARBOR 311110

11 CHUCK 311111

TABLE DRILLING MACHINE

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. On/off switch

2. Drill dept gauge

3. Protection guard

4. Motor

5. Drill dept lever

6. Table adjustment

Check first whether or not the delivery has been dama-

ged by transport and/or whether all the parts are pre-

sent.

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of

the instructions in this manual.

Denotes risk of electric shock.

Faulty and/or discarded electrical or electronic

apparatus have to be collected at the appropriate

recycling locations.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

Before using the machine the guidelines must be taken

into consideration. Every mechanical or electrical altera-

tion to the machine which does not meet the applicable

guidelines carries a considerable accident risk.

During use the following points must be taken

into consideration:

• Do not remove any mechanical or electrical protec-

tive provisions.

• Check whether all the protective provisions are in

place and have been attached correctly.

• Wear safety goggles during drilling.

• If you have long hair, be sure to wear hair protection

(hair net or cap). Long hair can easily be caught in

moving parts.

• Wear fitted clothing; tie buttons on sleeves.

• Do not hold any workpieces in your hands when dril-

ling. Always use a machine clamp or another clam-

ping tool.

• Protect workpieces and clamping tools on the bench

to prevent them from getting caught. Fasten them

yourself with screws or clamp them to a machine

clamp fastened to the table.

• Check whether the drill holder is tightened properly.

• Check whether cable lead-throughs are okay.

• To remove drill chips only use hand brushes, brus-

hes, rubber wipers, chip hooks or similar aids.

• Do not carry out any cleaning or greasing work while

the machine is in operation.

• Always keep V-belts covered (so that your hands

cannot become caught).

• Only tighten the toothed ring drill holder by means

of the wrench.

• Never leave the wrench of the drill holder in the drill

holder! Before switching on the machine, check

whether the wrench really has been removed!

• Do not use any drills which are damaged on the

shank.

• The drill is not suitable for moulding!

• If the mains cable is damaged, it may only be replaced

by a mains cable of the same type.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

ELECTRICAL INSTALLATION

The machine is provided with an electrical installation,

which meets the standards. Repairs may only be carried

Voltage | 400 V~

Frequency | 50 Hz

Power input | 1100 W

No load speed | 96-1988/min

Number of speeds | 9 (L/R)

Chuck capacity/Morse Conisch | 16 mm/MT4

Weight | 135 kg

Lpa (sound pressure level) | 88 dB(A)

Lwa (sound power level) | 101 dB(A)

Vibration value | <2,5 m/s

2

Ferm 3

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi FERM TDM1011 Pöytäporakone. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen FERM. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen FERM TDM1011 Pöytäporakone käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle FERM Pöytäporakoneet
Lisää Pöytäporakoneet käsikirjoja

Usein kysytyt kysymykset kohteesta FERM TDM1011 Pöytäporakone

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

FERM TDM1001 Pöytäporakone

Käyttöohje

FERM TDM1012 Pöytäporakone

Käyttöohje

FERM TDM1021 Pöytäporakone

Käyttöohje

FERM TDM1010 Pöytäporakone

Käyttöohje

FERM TDM1007 Pöytäporakone

Käyttöohje

FERM TDM1003 Pöytäporakone

Käyttöohje

FERM TDM1008 Pöytäporakone

Käyttöohje

FERM TDM1020 Pöytäporakone

Aiheeseen liittyvät luokat