Käyttöohje FERM CSM1013 Pyörösaha

Käyttöohje

• Never leave the circular saw unattended.

• Use this circular saw to saw only wood or wood-like

products.

SAFETY TIPS FOR THE LASER BEAMER

• Never look into the light beam of the laser.

• Never point the light beam of the laser at humans or

animals.

• Do not point the light beam of the laser at strongly

reflecting material. Hazard from reflected light.

• Only have repairs made to the laser beamer by

qualified personnel / professional repair specialists.

• Do not insert any hard objects into the laser optics.

• Clean the laser optics with a soft, dry brush.

USING THE MACHINE:

• Use clamps or a vice to hold the work.

• Never remove wood chips and saw dust that is close

to the saw blade with your hands. If there are small

pieces of wood left between the fixed and the

movable parts, the circular saw will have to be

stopped. The plug needs to be removed from the

socket, before any left piece can be removed.

• Check that the blade is suitable for the spindle speed

of the circular saw. Do not attempt to cut before the

circular saw has reached full speed. Make sure the

circular saw runs without load (i.e. is not in contact

with the work) when you switch it on. The circular

saw must have reached its full speed first.

• Never cut wood that is thicker than the depth of the

saw blade.

• When cutting in wooden walls or floors, check there

is no wiring or piping where you intend to cut.

• Switch off the tool and wait until the blade has

stopped completely before moving the saw away

from the work or putting it down. Hearing

protection should be worn when using circular saw.

SWITCH OFF THE MACHINE IMMEDIATELY

WHEN YOU DISCOVER:

•A defective mains plug or mains lead;

•A defective switch.

• Overheating of the circular saw.

• Smoke or odeur caused by scorched insulation.

ASSEMBLY AND

ADJUSTING INSTRUCTIONS

Before adjusting the saw, make sure the plug is

removed from the socket.

SETTING THE SAWING ANGLE (BEVEL)

Fig. B.

• Loosen the handle (1) that sets the sawing angle.

• Rotate the soleplate to the correct position (0° -

45°), and retighten the handle. The sawing angle

(bevel) can be read on the protractor (2).

FITTING THE RIP FENCE

Fig. B.

• Loosen the knob (3) that clamps the rip fence.

• Slide the rip fence into the special slot(6) in the sole

plate.

• Set the correct cut width and retighten the knob (3).

SETTING THE CUT DEPTH

Fig. C.

• Loosen the handle (1) that sets the sawing depth.

• Move the soleplate (2) downwards.

• The cutting depth of the saw blade can be read off the

curved scale attached to the upper side of the sole

plate.

• Retighten the handle (1) once the correct depth is set.

EXCHANGING OR CLEANING THE SAW

BLADE

Fig. D.

• Use the shaft locking knob (C3) to prevent the shaft

from rotating.

• Next, loosen the hexagonal bolt (3) in the centre of

the saw blade, using the box spanner.

• Turn the safety guard to the rear, and hold it there

with the aid of the knob (1).

• Remove the outside flange and the saw blade, and

clean the saw blade or replace it with a new one.

• Again place the saw blade back on the shaft. Ensure

that the teeth of the saw blade are pointing in the

same direction as the riving knife (4).

• Allow the safety guard to return over the saw blade

by releasing the knob (1).

• Press the shaft locking knob (C3) back in, refit the

outside flange (5) and tighten the hexagon bolt (3)

firmly, once more.

RENEWING AND REPLACING THE CARBON

BRUSHES

Fig. E.

• Remove the rear protective cover (no. 1) from the

motor casing, after first loosening the two Phillips

screws.

• Loosen the screw of the carbon brush holder.

• Withdraw the carbon brush holder from the casing,

and remove the old carbon brush.

• Fit the new carbon brush into the holder, and return

the holder to its location in the casing.

• Re-tighten the screw in the carbon brush holder.

• Replace both carbon brushes at the same time, and

never mix old and new brushes in this tool.

• Replace the rear protective cover (no. 1) on the

motor casing, and tighten the two Phillips screws.

Frequent use will cause the carbon brushes to wear

down. Regular inspection, after every 30 hours of

use, is essential. If the brushes have worn down to less than 4

mm, replace.

OPERATION

SWITCHING ON/OFF

Fig. E.

• Depress knob (B) with your right-hand thumb and

keep it depressed.

• Depress knob (A) to start the saw.

• Release knob (A) to stop the saw.

OPERATION

• Hold the work using clamps or a vice to have both

hands free to operate the saw.

4 Ferm Ferm 65

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi FERM CSM1013 Pyörösaha. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen FERM. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen FERM CSM1013 Pyörösaha käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle FERM Pyörösahat
Lisää Pyörösahat käsikirjoja

Usein kysytyt kysymykset kohteesta FERM CSM1013 Pyörösaha

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

FERM MSM1038 Pyörösaha

Käyttöohje

FERM CSM1037 Pyörösaha

Käyttöohje

FERM COM1007P Pyörösaha

Käyttöohje

FERM CSM1003 Pyörösaha

Käyttöohje

FERM CSM1034 Pyörösaha

Käyttöohje

FERM CSM1033 Pyörösaha

Käyttöohje

FERM CSM1016 Pyörösaha

Käyttöohje

FERM CSM1041P Pyörösaha

Aiheeseen liittyvät luokat