Home > Tee se itse > Kompressorit > FERM Kompressorit > FERM CRM1001 FCL-700 Kompressori

Käyttöohje FERM CRM1001 FCL-700 Kompressori

Tarvitsetko käyttöoppaan FERM CRM1001 FCL-700 Kompressori? Alta voit katsoa ja ladata suomenkielisen PDF-oppaan ilmaiseksi. Tällä tuotteella on tällä hetkellä 0 usein kysyttyä kysymystä, 0 kommenttia ja 0 ääntä. Jos tämä ei ole haluamasi käyttöopas, ota meihin yhteyttä.

Onko tuotteessa vika, eikä käyttöoppaasta ole apua? Siirry Repair Café ‑alueelle etsimään ilmaisia korjauspalveluita.

Käyttöohje

36 Ferm

MAINTENANCE

The mains plug always needs to be taken out of the

socket (the mains socket) during maintenance,

inspection or cleaning activities.

PERIODIC MAINTENANCE OF THE COMPRES-

SOR WILL PREVENT UNNECESSARY PROBLEMS!

FAULTS

Should a fault occur, e.g. after wear of a part, please con-

tact your local Ferm dealer.

In the back of this manual you find an exploded view

showing the parts that can be ordered.

POSSIBLE PROBLEMS AND REMEDIES

Fig. F

Air leaks through the pressure switch (1) when

the compressor is stopped

• Non return valve worn or dirty not working properly

• Dismantle the non return valve head clean rubber

disc (R) and/or replace it

• Reassemble with care.

Reduction in performance, starting too often or

low pressure

If the demand on the air supply remains the same, check

for air leaks on pipe and hoses, the conditions of the

intake filter or belt-driven regulation.

• Replace the seals of the fittings-clean or change air

intake cartridge.

• Recheck the regulation of belts

The motor or the pump overheats

Not enough cooling air on the motor or the pump.

• Check ambient temperature, oil level and quality,

intake filter, proper voltage.

The compressor stops after trying to start or

stops and will not start again

• The air tank is full. Improper voltage or lubrication

• Bad connection

• Check all parameter as before.

• If the problem is not resolved contact the specialist

service organisation

Anomal presence of oil in the compressed air.

• Excessive oil level.

• Wear of piston rings

• Check oil level

• Ask for Assistance

CONDENSATION

Humidity of the air wich condenses in the tank must be

drained, at least weekly through tap (6). If there is no oil

in the condensed water than it may be drained without

fear and pollution.

DRIVE BELTS TENSION

Drive belts require a precise tensioning of the belt

because at low values there are slippings on the pulley

causing overheating, and rapid wear of the belt. High

values cause excessive load on the bearing causing fast

wear of the same and motor over heating. The correct

tension value is obtained pushing with a screwdriver on

the intermediate area and you obtain a deflection of 1 cm.

OILLEVEL

The compressor comes with a special test oil, that must

be Replaced after about 100 hours of use. Check the oil

level from time to time, using the oil gauge.

When the compressor is level and has not been used for

some time, the oil level should be within the area indica-

ted by both marks on the gauge. The oil must be replaced

after every 300 hours of use or at least once a year. Use

compressor oil API CC SAE 40 rather than motor oil. If

the compressor is used in temperatures below 0°C, use

API CC SAE 20 oil.

EVERY MONTH

Clean the air filter

Every 300 working hours:

• Refresh the oil

• Carefully clean the outside of both the compressor

and the engine, to ensure an efficient cooling.

Condensation

• Regularly, drain condensation from the air chamber,

using the drain cock situated on the underneath of

the air chamber.

Have your compressor repaired by an expert!

This electric appliance is in accordance with the relevant

safety rules. Repairing of electric appliances may be car-

ried out only by experts other wise it may cause conside-

rable danger for the user.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations.

Take your unwanted machines to your local Ferm-

dealer. Here they will be disposed of in an environmen-

tally safe way.

GUARANTEE

The guarantee conditions can be found on the separately

enclosed guarantee card.

Ferm 5

Arviointi

Kerro meille mielipiteesi FERM CRM1001 FCL-700 Kompressori arvioimalla tuote. Haluatko jakaa tuotekokemuksesi tai kysyä kysymyksen? Jätä kommentti sivun alalaidassa.

Oletko tyytyväinen kohteeseen FERM CRM1001 FCL-700 Kompressori?
Kyllä Ei

Arvostele tuote ensimmäisenä

0 äänet

Keskustele tuotteesta

Täällä voit jakaa mielipiteesi FERM CRM1001 FCL-700 Kompressori:sta. Jos sinulla on kysyttävää, lue ensin huolellisesti käyttöohje. Käsikirjaa voi pyytää yhteydenottolomakkeellamme.

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi FERM CRM1001 FCL-700 Kompressori. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen FERM. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen FERM CRM1001 FCL-700 Kompressori käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.