Käyttöohje FERM CDM1044 Ruuvitaltta

Käyttöohje

5. If any wires on the charger are damaged, do not use it

until these have been replaced.

6. When the charger is not in use it should not be

plugged in. When unplugging, do not pull the plug out

by the cable.

7. If the charger breaks down or suffers from other

technical problems, take it to a recognised dealership

to be checked before using it again. Any damaged

parts must be replaced.

8. Take care when handling the accumulator block, do

not drop it or knock it against other things.

9. Never attempt to repair the battery charger or

accumulator block yourself; this can be extremely

dangerous. Repairs should always be carried out by a

recognised dealership.

10. Always unplug the charger before cleaning or

carrying out any other maintenance on it.

11. Do not attempt to charge the accumulator block in

temperatures of below 10 degrees or above 40

degrees centigrade.

12. The accumulator block must not be short-circuited.

When an apparatus short-circuits, the strength of

the electric current is increased. This can cause the

apparatus to over heat, catch fire or even explode, causing

damage and also endangering the operator.

To avoid this;

• Firstly do not connect any wires to the poles of the

accumulator block;

• Ensure that no metal objects (nails, coins, paper-clips)

are caught in the opening of the accumulator block;

• do not expose the accumulator block to water or rain.

13. If the accumulator block is broken or can no longer

be recharged it must be properly disposed off.

14. Never throw the accumulator block into water or a

fire – it may explode.

15. When drilling or screwing in walls, floors, etc.,

electricity lines can be hit. Hold the tool at the plastic

handle to prevent an electrical shock. Never hold the

tool at the chuck or another metal part.

16. Turn the drill immediately off after the screw is

fastened. Overloading and damaging the battery or

motor can be prevented this way. Use the torque to

loosen the fastened screw.

MOUNTING ACCESSORIES

INSERTING AND REMOVING BITS

Fig. C & D

When the ring is mounted, bits can easily be placed into

the hexagonal drive shaft:

• The bits can be placed directly on the tool, or on the

extension piece

• The sockets can be placed with help of the small

adapter piece (square-hexagonal)

Replace the ring by the keyless chuck, for using small

drills (max 6mm).

INSERTING AND REMOVING THE BATTERY

Fig. B

• Place the battery (6) at the bottom of the tool, as

shown in the figure. Ferm the battery until it snaps

into place.

• Ferm the release buttons (5) to remove the battery

from the bottom of the tool.

THE BATTERY LIFE SPAN

The battery life span is limited. If the run time of a loaded

battery shortens considerably, a new battery must be

purchased. If the tool is used irregularly, then charge the

battery at least once every six months for an optimal

result. When the battery is used under extreme hot or

cold circumstances the capacity will be less per charge.

OPERATION

Always observe the safety instructions and appli-

cable regulations.

Firmly hold the machine and ferm the bit with even

pressure into the workpiece. Do not force the machine.

Use only bits that do not yet show any signs of wear.

Worn bits have a negative effect on the efficiency of the

machine.

TORQUE ADJUSTMENT

Fig. E

The machine has different torque settings by means of

which the force for fastening and loosening screws can

be determined.

• Put the torque setting ring (2) at the required torque.

• Preferably select the lowest possible setting to move

the screw. Select a higher torque setting when the

motor is slipping.

• If the battery gets discharged, the motor will not slip

in position 4 or 5. Recharge the battery.

FASTENING AND LOOSENING SCREWS

• Ferm the top half of the direction switch (Fig. A. 3)

down to fasten screws (R).

• Ferm the lower half of the direction switch (Fig. A. 3)

up to loosen screws (L).

CHARGING BATTERIES

The battery that comes with the machine is not

fully charged.

• Only use the battery charger at temperatures

between +10 and +40 °Celsius.

• Only use the battery charger in dry rooms.

CHARGING

• Remove the battery from the machine

• Ferm the adapter plug of the charger into the battery

(near red LED)

• Plug the mains adapter into the (wall) socket

• The charging process starts; the red LED is now on

• If the battery is completely discharged or not used

for a long period, it takes about 24 hours to charge

the battery. Normally it takes about 5 hours.

• Place the battery in the tool after charging.

4 Ferm Ferm 53

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi FERM CDM1044 Ruuvitaltta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen FERM. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen FERM CDM1044 Ruuvitaltta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle FERM Ruuvitaltat
Lisää Ruuvitaltat käsikirjoja

Usein kysytyt kysymykset kohteesta FERM CDM1044 Ruuvitaltta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

FERM CDM1074 Ruuvitaltta

Käyttöohje

FERM CDM1049 Ruuvitaltta

Käyttöohje

FERM CDM1080 Ruuvitaltta

Käyttöohje

Einhell TH-DY 500 E Ruuvitaltta

Käyttöohje

Elu BS45EK Ruuvitaltta

Käyttöohje

Black and Decker VPX1101 Ruuvitaltta

Käyttöohje

Bosch IXO Ruuvitaltta

Käyttöohje

Parkside IAN 413972 Ruuvitaltta

Aiheeseen liittyvät luokat