Käyttöohje Bort BAS-48N-LT Ruuvitaltta

Käyttöohje

7

GB

Cordless screwdriver

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1. On/off switch

2. Bit holder

3. Switch for changing direction of rotation

4. Ring for torque control

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, fi re

and/or serious injury.

• Recharge only with the charger specifi ed by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of fi re when used with another

battery pack.

• Use power tools only with specifi cally designated battery

packs. Use of any other battery packs may create a risk

of injury and fi re.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the charger

(chargers with a rating of 230V or 240V can also be con-

nected to a 220V supply)

• In case of electrical or mechanical malfunction, imme-

diately switch off the tool or unplug charger from power

source

• SBM Group can assure fl awless functioning of the tool

only when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• This tool should not be used by people under the age of

16 years

• Be careful not to drill or drive into areas where electrical

wires may be contacted

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Never charge battery outdoors

• Store tool/charger/battery in locations where tempera-

ture will not exceed 40° C or drop below 0° C

• Batteries will explode in fi re, so do not burn battery for

any reason

• When damaged, and under extreme usage and tem-

perature conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, fl ush eyes with clean water for

a minimum of 10 minutes and seek immediately medical

attention

• When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc.

to prevent short-circuit

• Do not use charger when damaged; take it to one of the

offi cially registered SBM Group Service Stations for a

safety check

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries

with the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of the charger to the earth terminal of

the plug

• If for any reason the old plug is cut off the cord of

the charger, it must be disposed of safely and not left

unattended

To ensure longer service life and proper per-

formance of the battery, take the following ac-

tions when you start using new battery:

1. Use the new battery, without recharging it, till its com-

plete discharge.

2. Then charge the battery for 3-5 hours.

3. Repeat abovementioned actions (1 and 2) 3-5 times to

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please

contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these ma-

terials to the appropriate recycling locations. Take your

unwanted machines to your local SBM Group dealer.

Here they will be disposed of in an environmentally safe

way.

NiCd batteries can be recycled. Deliver them to a dispos-

al site for chemical waste so that they can be recycled or

disposed of in an environmentally friendly manner.

English

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Bort BAS-48N-LT Ruuvitaltta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Bort. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Bort BAS-48N-LT Ruuvitaltta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Bort Ruuvitaltat
Lisää Ruuvitaltat käsikirjoja

Usein kysytyt kysymykset kohteesta Bort BAS-48N-LT Ruuvitaltta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Bort BAS-36N-Li Ruuvitaltta

Käyttöohje

Bort BAS-36-Li-T Ruuvitaltta

Käyttöohje

Bort BAS-36N-LT Ruuvitaltta

Käyttöohje

Einhell TE-CW 18 Li BL-Solo Ruuvitaltta

Käyttöohje

AEG BTS12C Ruuvitaltta

Käyttöohje

Black and Decker AS600 Ruuvitaltta

Käyttöohje

Black and Decker KC9039 Ruuvitaltta

Käyttöohje

FERM CDM1080 Ruuvitaltta

Aiheeseen liittyvät luokat