Käyttöohje Black and Decker KS1880S Puukkosaha

Käyttöohje

5

ENGLISH

◆ Move the blade clamp lever (5) down to lock the blade

clamping mechanism.

◆ Remove the tooth protector, if fitted.

Note: This tool has been designed to allow the saw blades to

be fitted with the teeth facing forward or backward.

Use

Charging the battery (fig. A)

The battery needs to be charged before first use and whenever

it fails to produce sufficient power on jobs that were easily

done before. When charging the battery for the first time, or

after prolonged storage, it will only accept an 80% charge.

After several charge and discharge cycles, the battery will

attain full capacity. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery (6), remove it from the tool.

◆ Slide the charger receptacle (9) onto the battery as shown.

◆ Plug in the charger (8). Switch on at the mains.

The battery will become warm while charging. After approx.

3 hours of charging, the battery will be sufficiently charged for

use in regular applications. After approx. 6 hours of charging,

the battery will be fully charged.

◆ Remove the charger receptacle from the battery.

Switching on and off

◆ To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

Sawing (fig. C)

◆ Always hold the tool with both hands.

◆ Let the blade run freely for a few seconds before starting

the cut.

◆ Apply only a gentle pressure to the tool while performing

the cut.

◆ If possible, work with the shoe pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being damaged.

Hints for optimum use

Sawing wood

◆ Clamp the workpiece securely and remove all nails and

metal objects.

◆ Holding the tool with both hands, work with the shoe

pressed against the workpiece.

Pocket cutting in wood

◆ Measure and mark the required pocket cut.

◆ Fit a saw blade suitable for pocket cutting.

◆ Rest the shoe on the workpiece in such a position that the

blade forms an appropriate angle for the pocket cut.

◆ Switch on the tool and slowly feed the blade into the

workpiece. Make sure that the shoe remains in contact

with the workpiece at all times.

Sawing metal

◆ Be aware that sawing metal takes much more time than

sawing wood.

◆ Use a saw blade suitable for sawing metal.

Use a fine-tooth saw blade for ferrous metals and a

coarser saw blade for nonferrous metals.

◆ When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

◆ Spread a film of oil along the intended line of cut.

Cutting branches

Branches up to 25 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or

on any other unstable surface. Be aware of where the branch

will fall.

◆ Cut downward and away from your body.

◆ Make the cut close to the main branch or tree body.

Vertical cutting

The tool allows close cutting to corners and other difficult areas.

◆ Insert the shank of the saw blade into the blade holder

with the teeth of the blade facing upward.

◆ Hold the tool with the shoe facing downward so that you

are as close to the work surface as possible.

◆ Cut forward and away from your body.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

MAINTENANCE

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning. Your charger does not require any

maintenance apart from regular cleaning.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Black and Decker KS1880S Puukkosaha. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Black and Decker. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Black and Decker KS1880S Puukkosaha käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Black and Decker Puukkosahat
Lisää Puukkosahat käsikirjoja

Usein kysytyt kysymykset kohteesta Black and Decker KS1880S Puukkosaha

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Black and Decker CHS600 HandiSaw Puukkosaha

Käyttöohje

Black and Decker HPL10RS Puukkosaha

Käyttöohje

Black and Decker CHS6000 HandiSaw Puukkosaha

Käyttöohje

Black and Decker RSP1050 Puukkosaha

Käyttöohje

Black and Decker RS1050E Puukkosaha

Käyttöohje

FERM RCM1001 Puukkosaha

Käyttöohje

AEG USE 600 Puukkosaha

Käyttöohje

Hitachi CR 18DV Puukkosaha

Aiheeseen liittyvät luokat