Käyttöohje Black and Decker HP9012 Ruuvitaltta

Käyttöohje

5

ENGLISH

◆ Under extreme conditions, battery leakage may occur.

When you notice liquid on the battery, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin

contact.

- In case of skin or eye contact, follow the instructions

below.

Warning! The battery fluid, a 25-30% solution of potassium

hydroxide, can be harmful. In case of skin contact, immediately

rinse with water. Neutralise with a mild acid such as lemon

juice or vinegar. In case of eye contact, rinse abundantly with

clean water for at least 10 minutes. Consult a physician.

◆ Do not incinerate the battery.

◆ Do not attempt to charge damaged batteries.

Chargers

◆ Use your Black & Decker charger only to charge the battery

in the tool with which it was supplied. Other batteries

could burst, causing personal injury and damage.

◆ Never attempt to charge non-rechargeable batteries.

◆ Have defective cords replaced immediately.

◆ Do not expose the charger to water.

◆ Do not open the charger.

◆ Do not probe the charger.

The charger is intended for indoor use only.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

Overview (fig. A)

1. Variable speed switch

2. Forward/reverse slider

3. Bit holder sleeve

4. Head adjustment button

5. Charger receptacle

6. Charger

7. Screwdriver bit

8. Battery

Assembly

Fitting and removing the battery (fig. B)

◆ To fit the battery (8), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

◆ To remove the battery, push the release button (9) while

at the same time pulling the battery out of the receptacle.

Fitting and removing a drill bit or screwdriver bit

(fig. C & F)

This tool uses screwdriver bits and drill bits with a 1/4"

(6.35) mm hexagonal shank.

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position (fig. F).

◆ Pull back the bit holder sleeve (3) (fig. C).

◆ Insert the bit shaft (7) into the bit holder.

◆ Release the bit holder sleeve.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Charging the battery (fig. E)

The battery needs to be charged before first use and whenever

it fails to produce sufficient power on jobs that were easily

done before.

When charging the battery for the first time, or after

prolonged storage, it will only accept an 80% charge.

After several charge and discharge cycles, the battery will

attain full capacity. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery (8), remove it from the tool.

◆ Slide the charger receptacle (5) onto the battery as

shown.

◆ Plug in the charger (6).

The battery will become warm while charging. After approx. 3

hours of charging, the battery will be fully charged.

◆ Remove the charger receptacle from the battery.

Adjusting the head (fig. D)

For optimum versatility, the head can be set to different positions.

◆ Press the head adjustment button (4) down.

◆ Swivel the head into the desired position.

◆ Release the button.

Selecting the direction of rotation (fig. F)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

Arviointi

Lisää tästä ohjekirjasta

Ymmärrämme, että on mukavaa, että sinulla on paperikäyttöinen käyttöopas laitteellesi Black and Decker HP9012 Ruuvitaltta. Voit aina ladata oppaan verkkosivuiltamme ja tulostaa sen itse. Jos haluat alkuperäisen käyttöoppaan, suosittelemme ottamaan yhteyttä osoitteeseen Black and Decker. He saattavat pystyä toimittamaan alkuperäisen ohjekirjan. Etsitkö laitteen Black and Decker HP9012 Ruuvitaltta käyttöopasta toisella kielellä? Valitse haluamasi kieli kotisivuiltamme ja etsi mallinumero nähdäksesi, onko sitä saatavilla.

Tekniset tiedot

Kaikki käsikirjat kohteelle Black and Decker Ruuvitaltat
Lisää Ruuvitaltat käsikirjoja

Usein kysytyt kysymykset kohteesta Black and Decker HP9012 Ruuvitaltta

Tukitiimimme etsii hyödyllisiä tuotetietoja ja vastaa yleisiin kysymyksiin. Jos huomaat yleisissä kysymyksissä virheen, kerro siitä meille yhteydenottolomakkeella.

Liittyvät tuotteet

Käyttöohje

Black and Decker BCF602 Ruuvitaltta

Käyttöohje

Black and Decker KC460LN Ruuvitaltta

Käyttöohje

Black and Decker BDCS36G Ruuvitaltta

Käyttöohje

Black and Decker KC360NM Ruuvitaltta

Käyttöohje

Black and Decker XTC60K Ruuvitaltta

Käyttöohje

Black and Decker KC9006 Ruuvitaltta

Käyttöohje

Black and Decker AS600 Ruuvitaltta

Käyttöohje

Black and Decker BDCSFS30 Ruuvitaltta

Aiheeseen liittyvät luokat